Cequent Performance Products PRO KR Serie Guia De Inicio Rapido

Read, Understand, Follow and Save These Instructions
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product only as
specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never allow installation
or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions and warnings for any
product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a reference for any future installation
and use of the product.
WARNING
This product must be installed and used in strict
accordance with these instructions. Purchaser/
owner must not alter or modify the product.
Operator and bystanders should never position
any part of body under or on the path of any
portion of this product or the load being
supported, or moved.
Do not allow children to play on or around this
product or the load being supported, or moved.
Do not use winch to move humans.
Never exceed the maximum rated capacity. Refer
to stamped markings on side of frame to obtain
rated capacity. If uncertain, contact Cequent
Performance Products at 1-800-521-0510 or
www.cequentgroup.com
Always inspect the cable and its attachment
before each use for damaged of any kind. Never
use worn, kinked, or frayed cable or attachment.
Never stand along side the winch cable, strap, or
Installation Instructions
HANDLE ATTACHMENT AND WINCH MOUNTING
1) Insert handle onto input shaft hexagon end. Align screw holes
and drive shaft indents (Fig. 1). Tighten the set screws with
the wrench provided. Note: Do not remove or adjust any
hardware on the input shaft except the handle. This is critical
to the braking system and must be left intact.
2) Mount the winch to a structure capable of supporting at least 3
times the load the winch will be pulling. (Mounting hardware
not supplied.) The mounting surface must be equal to or
greater than the footprint of the winch frame. Mounting
bolts will vary in length for each application. Note: When
bolting the winch down, use three grade 5, 3/8 diameter
bolts, flat washers and locknuts and torque to 30 ft-lbs.
Always use outer most slots at the end opposite the direction
of line pull. Use large flat washer if using center slot at
opposite end.
CABLE ATTACHMENT TO DRUM
1) Feed the cable over the top of drum and through the drum side
slot. Insert cable end through one side of cable clamp and loop
back into the other side as shown in Fig. 2. Tighten clamp nut
slightly and reduce loop by pulling cable (see Fig. 3).
2) Tighten cable clamp nut until cable is adequately clamped
(approximately 20-30 in-lbs.) Replace cable clamp each time
cable is replaced.
3) Always be sure the cable is pulling straight off the winch, not
at an angle. This will prevent the cable from rubbing against
the sides of the drum, which can damage the cable. Neatly
wrapping the cable is necessary to reduce the chance of
kinking, fraying or any other damage to the cable.
KR Series Work Winches
Failure to follow all warnings and instructions may result in product
failure, property damage, serious bodily injury, and/or death.
rope or guide the cable, strap, or rope with your
hands.
Never operate with slippery, wet, or oily hands
and always maintain a firm grip on the winch
handle. Do not attempt to stop a winch by
grabbing the handle while in motion.
Always maintain a minimum of three complete
wraps of cable or rope on the drum, or three
layers of strap on the drum.
Assure there is adequate safety factor, of at least 3
times the maximum load capacity for all
components used in conjunction with this
product.
A loud clicking sound from the ratchet must be
heard when lifting the load. If a loud clicking
sound is not heard, do not use.
Never release the crank handle unless the ratchet
pawl is fully engaged and the load is supported.
Never leave a weight supported from the winch
Warning: Failure to follow all warnings and instructions may result in
product failure, property damage, serious bodily injury, and/or death.
Fig. 1
Fig. 2
while the winch is unattended, as another person
may attempt to operate the winch, thereby
creating an unsafe condition.
This winch is designed for manual operation only
and the maximum load rating is based on an
intermittent use cycle.
Excessive force in turning winch handle may
indicate overload. Pro Series brand winches
require 25-45 lbs of handle force to pull their
rated load.
If you cannot crank the winch with one hand you
are potentially overloading the winch.
Winches are not designed to secure boats to
trailers while towing. Boat tie downs should be
used for this purpose.
Periodically check mounting hardware for proper
torque and tighten if necessary.
Always replace bent, broken, or worn parts before
using this product.
Align screw
holes and
indents
Push
Fig. 3
Screw in tightly
F3566 (Rev-B 12699)