SLIDING DOOR HARDWARE - Pocket Door
table 1: Key Dimensions by Door Width (D)
Header Length
24" [610]
30" [762]
36" [914]
Custom
(2 x D) - 1-3/8"
1
SIZE tRACK & HEADER
• The header assembly comes configured for 3' doors.
• For alternate door widths cut header and nailing
strips to length shown in Table 1.
Note: Track will be 1-1/2" shorter than header.
B) Turn on side to cut nailing boards. Cut both nailing boards at
required mark line. Being careful NOT to cut header board or track.
B) Tournez sur le côté pour couper les fonds de clouage. Coupez
les deux fonds de clouage à la ligne de marquage requise.
B) Gire sobre su lado las placas para clavar. Corte ambas placas
para clavar por la línea de marca requerida.
2
PREPARE ROuGH OPENING
• Prepare rough opening width based on values
from Table 1 and rough opening height based
on values from Table 2.
• Mark each side of rough opening above finished floor
at bracket nail height dimension in Table 2.
• Slide the slot in the "pocket" end bracket over
nail head, level with doorway bracket and
seat nail. Double check, level and
drive additional nails as shown.
• "Doorway" end bracket
mounts to jamb in
"doorway" level
and secure with
additional nails.
• If floor covering
(carpet, etc.) is more
than 1/4" in thickness:
1. Cut off bottom of door
OR
2. Use sole strip in pocket opening
equal to thickness of floor covering and
as wide as the width of the frame.
table 2: Dimensions by Door Height
Rough Opening
Opening
Height
6'8" door
85-1/8"
7' door
89-1/8"
8' door
101-1/8"
(If floor covering to be used is greater than 3/4" thick,
a sole strip of equal thickness must be added OR an
equal amount can be cut off the bottom of the door.)
Nailing Strip Length
(t)
(H)
46-5/8"
25"
58-5/8"
31"
72-5/8"
37"
D + 1"
Doorway
Entrée de porte
Entrada
Bracket
Nail Height
81-3/8"
85-3/8"
97-3/8"
Rough Opening Width
Note: In the following illustrations,
(W)
the doorway opening is to the left.
49"
Nota: Dans les illustrations suivantes,
61"
l'ouverture d'entrée de porte est à gauche.
73"
Nota: En las figuras siguientes, la apertura
(2 x D) + 1"
de la entrada es hacia la izquierda.
Note: Markings for standard door
widths.
Nota: Marques pour largeurs de
porte standard.
Nota: Marcas para anchuras de
puerta estándar.
C) Turn track assembly over
and cut track 1-1/2" shorter than
wood header.
C) Retournez l'ensemble de rail et
coupez le rail à 3,8 cm de
l'extrémité du linteau en bois.
C) Gire el conjunto del carril y corte el carril a 3,8 cm más
atrás del extremo de la cabecera de madera.
Bracket Nail Height
Hauteur de Clou de Support
Altura del clavo del soporte
Opening Height
Hauteur d'Ouverture
Altura de la abertura
Width (from Table 1)
Largeur (Du Tableau 1)
Anchura (de la Tabla 1)
#310309_C (1013)
Assembly
Instructions
A) Cut wood header at stamped size
mark line.
A) Coupez le linteau en bois à la ligne
de marquage de taille estampée.
A) Corte la cabecera de madera por la
línea de marca de tamaño estampada.
Pocket
Partie
coulissante
escamotable
Cavidad
Finished floor OR Sole Strip
Sol fini Ou Semele
Piso acabado O listón del piso
