Overhead door Master Manual De Instrucciones

37385500131
Moving door can cause serious injury or death.
• Do Not install transmitter unless the door operator's safety reverse works as
required by the door operator's manual.
• Wall control must be mounted in sight of door.
• Keep people clear of opening while door is moving.
• Do Not allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
• Close door then disconnect operator using the manual release handle.
• Do Not use transmitter or door operator.
• Refer to Door and Door Operator Owner's Manuals before attempting any repairs.
A. For use with CodeDodger® 1 Openers—
The Universal Remote comes from the factory in the CodeDodger® 1 Operating Mode. The CodeDodger®1 Mode is
indicated by a RED LED on the remote whenever a button is pressed (FIG. 2).
Program it as you would any CodeDodger® 1 remote using the following steps:
1. Locate the Learn Code Button and Learn Code Indicator LED on your opener's powerhead (FIG. 1)
(See owner's manual).
2. Press and release the Learn Code Button—the Learn Code LED will blink rapidly.
3. Press and release a Remote Button, (FIG. 2)—the Learn Code LED will stay on (stops blinking)
4. Press and release the same Remote Button again—the Learn Code LED will turn o .
5. Press and release the same Remote Button again—the Door Opener will run.
NOTE: Each opener must have its own assigned Remote Button. To program additional openers, repeat the steps
above using a di erent Remote Button.
B. For use with CodeDodger® 2 Openers—
The button or buttons on your remote that you wish to use to operate CodeDodger® 2 openers, must be switched to
the CodeDodger® 2 Operating Mode. The CodeDodger® 2 Mode is indicated by a GREEN LED on the remote whenever
a button is pressed (FIG. 2).
To shift to CodeDodger® 2 mode:
1. Press and hold the chosen Remote Button—A steady RED LED will be illuminated and after 10 seconds—
a GREEN LED will also illuminate.
2. Release the button.
3. Press and release that same button again TWICE—the remote's LEDs will both turn o .
4. Press and release that same button again—the remote's GREEN LED will light while you press that button
indicating it is now in CodeDodger® 2 mode.
To program the remote to an opener:
1. Press and hold the PROGRAM/SET (FIG. 1) button on opener's powerhead for 2 seconds or until the round
LED turns BLUE. When you release the button the BLUE LED will go out and the LONG LED will turn PURPLE.
2. Press and release the Remote Button you want to assign to that opener.
3. Press and release that same button. After releasing the button the second time, the LEDs will both be o .
4. Press and release that same button again—the Door Opener will run.
C. For use with Openers having a row of Code Switches (9 or 12 switches).
(If you already have a working "code switch" remote, simply match your new Master™ Remote switches to those
on your existing remote and proceed to step 4.)(FIG.3)
To operate a Code Switch equipped operator:
1. Open the opener's light lens in order to gain access to its row of Code Switches.
These are 3 position switches (+, – and 0).
2. Slide o the rear cover of the remote (FIG. 3).
3. Set the Code Switches positions in the remote to match those of the switches in the opener. (If you are
working with a 9 switch operator, set the remote switches 10, 11 and 12 to the center or "0" position)
4. Locate the non-rolling code button label inside the Rear Cover (FIG. 3).
5. Press the non-rolling code button B, C or D (FIG.3) that matches the appropriate code switch description
on the label. The YELLOW LED next to the battery will begin ashing.
6. Press and release the Remote Button you want to assign to that opener—the GREEN LED on the remote
will ash for approximately 2 seconds and stop.
7. Pressing the same button again will operate the opener—The RED LED on the remote will ash while
the button is pressed.
D. Replacing the Battery. (Programming is not a ected by battery replacement.)
1. Slide the Circuit Board Cover o the back of the remote (FIG. 3).
2. Slide the old battery toward the bottom of the remote and out.
3. Properly discard the old battery.
4. Slide a new (2032 size) battery into position and slide the Cover back on.
E. Resetting the Remote
To return a Remote Button to its original CodeDodger® 1 mode:
1. Slide the Circuit Board Cover o (FIG. 3).
2. Press the DEFAULT button—the yellow LED will ash.
3. Press the Remote Button you wish to reprogram. Its now CodeDodger® 1 again.
FCC & IC CERTIFIED
This device complies with part 15 of the FCC Rules and IC RSS 210 Issue 8. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular situation. If this equipment does cause harmful
interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try and correct the interference by one or more of the following measures:
(a) Re-orient or relocate the receiver antenna, (b) increase the separation between the opener and receiver, (c) Connect the opener into an outlet on a circuit different from that which the receiver is connected, and
(d) Consult your local dealer. Any modifications or changes to this equipment which are not expressedly approved by The Overhead Door® Corporation could void the user's authority to operate the equipment.
Master
TM
TRANSMITTER OPERATION
WARNING
FIG. 1 POWERHEADS
Circle indicates location of Learn Code Button and LED.
PRIOR TO 1995 AND
CODEDODGER®
CODE SWITCH TYPE
CODEDODGER® 1 —1995 TO PRESENT
FRONT
BACK
OPEN
SET
LEARN MANUAL LIMIT FORCE
SET
CODE CLOSE
LEARN
CODE
BOTTOM
CODEDODGER 2 2010 TO PRESENT
BOTTOM
FIG. 2
REMOTE
BUTTONS
FIG. 3
1
-
0
+
1 2 3 4 5 6 7 8 9 10 11 12
-
DEFAULT 0
NON ROLLING CODE
+
ECE
BUTTON
B C BUTTONS
9-TRI
A IC/CD 1 12-BIT D
DEFAULT 9-BIT
YELLOW
BATTERY
LED
REAR COVER INSIDE REAR COVER
FOR HELP OR ANSWERS TO QUESTIONS, CALL
800 929 3667 or visit www.overheaddoor.com
(for various models)
FRONT
FRONT
INSIDE LIGHT LENS
PRGM
– +
SET
LEDs
(red/green)
2 3 4 5 6 7 8 9 10 11 12
ECE
CODE SWITCHES