Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3.0 Safety warnings
1.
Read and understand the entire owner's
manual for both the tenoning jig and the table
saw, before attempting assembly or operation.
2.
Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3.
Replace warning labels if they become
obscured or removed.
4.
This tenoning jig is designed and intended for
use with a table saw. If you are not familiar with
the proper and safe operation of a table saw, do
not use saw or tenoning jig until proper training
and knowledge have been obtained.
5.
Do not use this tenoning jig for other than its
intended use. If used for other purposes,
Powermatic disclaims any real or implied
warranty and holds itself harmless from any
injury that may result from that use.
6.
Always wear ANSI Z87.1 approved safety
glasses or face shield while using this tenoning
jig. (Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
7.
Before operating a table saw or tenoning jig,
remove tie, rings, watches and other jewelry,
and roll sleeves up past the elbows. Do not
wear loose clothing. Confine long hair. Non-slip
footwear
or
anti-skid
recommended. Do not wear gloves.
8.
Kickback occurs when a workpiece is thrown
towards the operator at a high rate of speed. If
you do not have a clear understanding of
kickback and how it occurs, do NOT operate a
table saw!
9.
Wear hearing protection (plugs or muffs) during
extended periods of operation.
10. Some dust created by power sanding, sawing,
grinding,
drilling
activities contain chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
Lead from lead based paint.
•
Crystalline silica from bricks, cement and
other masonry products.
•
Arsenic and chromium from chemically
treated lumber.
floor
strips
and
other
construction
Your risk of exposure varies, depending on how
often you do this type of work. To reduce your
exposure to these chemicals, work in a well-
ventilated area and work with approved safety
equipment, such as face or dust masks that are
specifically designed to filter out microscopic
particles.
11. Do not operate table saw or tenoning jig while
tired or under the influence of drugs, alcohol or
any medication.
12. Make certain switch is in OFF position before
connecting table saw to power supply.
13. Make certain the table saw is properly grounded
before
documentation to verify if any steps need to be
taken for grounding.
14. Turn off table saw, allow blade to stop
completely, and disconnect table saw from
power before attempting adjustments to jig or
workpiece.
15. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the tenoning jig
and table saw before turning on saw.
16. Keep both hands on jig operating handles when
processing workpiece with the tenoning jig.
Always keep hands out of the line of saw blade.
17. Make certain workpiece is securely clamped in
place and all handles are properly tightened
before operating table saw and jig.
18. Reinstall
tenoning operations.
19. Never reach around or over the saw blade.
are
20. Check for damaged parts. If damage is
suspected,
service for assistance.
21. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
22. Keep the floor around the machine clean and
free of scrap material, oil and grease.
23. Keep visitors a safe distance from the work
area. Keep children away.
24. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
25. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in serious
injury.
26. Maintain a balanced stance at all times so that
you do not fall into the blade or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
4
using
jig.
Refer
to
blade
guard
immediately
contact
Powermatic
table
saw
after
customer
Capítulos
Tabla de contenido
