Chamberlain 8002E Manual De Instrucciones página 2

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 5
DISCONNECT POWER TO GARAGE
DOOR OPENER BEFORE INSTALLING
RECEIVER.
For use with the following RF modules:
To operate the control board via radio, a radio module
must first be installed in slots CN1/CN2.
• 801221
Superheterodyne, 433.92MHz
• 801344
Superregenerative, 418MHz
The 2 Channel Universal Receiver Model 8002E can
be programmed to receive up to 15 codes for each
channel.
INSTALLATION
The receiver should be mounted towards the front of the garage, preferably
about two meters above the floor. Select a location which allows clearance
for opening the cover, and space for the antenna (as far from metal
structures as possible). The receiver and antenna use TV Type F coaxial
connectors. The antenna is threaded directly onto the receiver. An additional
cable extension (86LM) is available to improve the range
The transformer (Model 23009E) must be plugged into the wall within two
meters of the receiver, to allow the wire to reach the receiver terminals.
1. Fasten the receiver securely with screws through the corner holes which
are located under the cover.
2. AC/DC are the terminals on the circuit board. (see illustration)
Connect the transformer wire to the terminals.Now tighten
terminals.
3. Connect operator control board to the terminals of the Universal
Receiver. In this process, connect the cable of te wall-button to terminals
(Channel A). Connect the cable of the second wall-button ( if you have to
operate 2 doors) to the terminals . (Channel B). In case there is no wall-
button or keyswitch, consult the manual of your garage door opener.
4. Plug in the transformer and reconnect power. You may use the
Test button to operate your opener(s).
PROGRAMMING THE RECEIVER TO ACCEPT
YOUR TRANSMITTER CODE
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or
leave garage while door is in motion. Do not allow children to
operate push button(s) or remote(s). Do not allow children to
play near the door.
1. Press and hold the remote control push button.
2. Press and release the Learn button in the Control Center on the opener
panel. The indicator light will flash once.
3. Release the remote push button.
Now the opener will operate when the remote control push button is
pressed.
If you release the remote control push button before the indicator
lights flash, the opener will not accept the code.
Repeat steps 1 – 3 to program the receiver for all remote controls in use for
that door. If a second door is in use, use a different remote control button
and repeat the steps for channel B.
Replace top cover with mounting screws.
To erase all codes from the receiver: hold the receiver's Learn button until
the indicator light goes off (after 6 seconds). All codes that the receiver has
learned will be erased.
All manuals and user guides at all-guides.com
The receiver can be set for either constant or momentary closure on the
output contacts for each channel (A and B). (Use constant closure only if
constant pressure is needed.) With the jumper in "1" (Momentary) position,
the contacts will close for 150ms regardless of the length of radio
transmission. With the jumper in "2" (Constant) position, the contacts will
stay closed as long as the radio continues transmitting.
Indicator lights
(momentary or constant)
> 24V
16-30V AC, @ 30mA
24-30V DC, @ 30mA
Universal 2 Channel Receiver
SPECIFICATIONS
Output Rating ......................................I max. = 5 A; V max. = 30V AC/DC
Power input
<24V .................................................9-16V AC, @ 30 mA
...................................................................................9-24V DC, @ 30 mA
.................................................................................16-30V AC, @ 30 mA
>24V ................................................24-30V DC,@ 30 mA
RF Frequency ...........................................................418MHz, 433.92MHz
TO SET OUTPUT DURATION
Momentary
LDS2
LDS1
CN2
Jumper
Channel B
>24V < 24V
< 24V
9-16V AC, @ 30mA
9-24V DC, @ 30mA
Model 8002E
Constant signal
(Hold to run)
Antenna Connection
optional
Ant.
CN1
A
B
LDS3
LDS4
Test
Test
(Channel A & B )
Jumper
LearnA
LearnB
Channel A
Input
OUT A OUT B
AC / DC
Indicator lights
(Channel A & B)
Command buttons
(Channel A & B)
Program buttons
Transformer
Tabla de contenido
loading

Tabla de contenido