Safety Messages; Use As Directed - LIM 2 Instrucciones De Manejo

ENGLISH
USER MANUAL FOR
LED RGB CONTROLLER
LIM®2
Read this short manual carefully and keep it accessible for further reference!

SAFETY MESSAGES

Disregard of the safety messages may lead to danger of life, burning or fire!
• The product may not be modified or converted.
• Do not hang or fasten anything on the product, especially no decoration.
• Do not cover the product - provide free air circulation.
• In case of a malfunction you may NOT touch the product or operate it further.
Disconnect the product from the power supply by an external switch or by the
fuse.
A malfunction exists when:
• visible damages appear.
• the product does not work properly (e.g. flickering).
• smoke, steam or crackling sounds appear.
• smell of burning is recognisable.
• an overheating is recognisable (e.g. by discolouration of adjacent surfaces).
Operate the product only after maintenance and examination by an approved
electrician!
• This product is not intended to be used by children. Ensure that children do not
suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:

USE AS DIRECTED

This product serves controlling light purposes and may:
•
only be used with a voltage of 230V ~50Hz.
• only be installed according to safety class II (two).
• only be operated when firmly mounted on a stable, even and tilt-fixed surface.
• only be operated on normally or not flammable surfaces.
• only be used in dry condition,
• not in damp or dirt-endangered rooms.
• not in areas of high air humidity.
• not be exposed to strong mechanical loads or to strong contamination.
MAINTANANCE AND CARE
Care
Disconnect the product from the power supply and let it cool down, before you
clean the product.
• Clean the product on a regular basis using a slightly moistened, soft and fluff-free
cloth. Please also note additional supplied notes on maintanance and care.
®
FUNCTION OF THE LIM 2 CONTROLLER
Get familiar with the possibilities and functions of the LIM
the device into service:
®
The LIM 2 controller serves controlling coloured light(RGB) using colour
programs. A colour program consists of 1-8 scenes. One scene equals one colour.
One colour is created by additive colour mixture of the three colour channels
Red(R), Green(G), Blue(B). With a run of a colour program the scenes elapse in
succession.
There are eight colour programs to use. Four programs are pre-programmed.
Rainbow Sundown
Colours of a Colours of a
rainbow sundown
The four other programs may be freely programmed by the user:
User A User B
Additionally there are further adjustments possible during operation:
• Type of transition of the scenes(colours): This setting determines if the colors
change directly (hard) or shift over in one another (soft). This setting is valid for
all scenes within a program.
• Duration of a scene: This setting determines how long a scene is active.
Possible are adjustment between 1 second and 240 minutes. This setting is valid
for all scenes within a program.
Switching contact (SK)
When using the switching contact the following adjustments are possible:
• Setting Intern: When the switching contact is closed all four outputs are operated
on 100% (=white light) – panic function.
• Setting Extern: When the switching contact is closed the running colour program
is stopped. When the switching contact is open the colour program starts.
.
®
2 controller before putting
IceBlue Fantasy
Cool hues in
blue
User C User D
OPERATION
When the product is put into service the display shows the following:
(Please note, that the indications no. 2-4 and 6 may vary since these are
based on previous settings. This may also be the case with the following
figures of the display.)
Program IceBlue
1
Hard Intern
3
Time 002 sec
5
Run
7
1 Here the current mode is displayed.
Hier wird angezeigt in welchem Modus sich das Gerät befindet.
Program: regular operating mode
Select: modification mode
Program Editor: programming mode
2 Menu point Program
Displays the currently chosen
colour program
4 Menu point Switching
contact: Displays how the
switching contact is used
(Intern or Extern)
6 Menu point time unit:
Displays the time unit (sec or
min)
There are buttons located beneath the display.
Mode Set Enter + -
Button(s) Function
Mode Switching between the regular operating mode to the
modification mode to the programming mode.
Set Selecting a menu point to change
Enter Confirmation of made entries
+/- Jumping to menu points and changing of settings
Start/Stop Starts respectively stops the current colour program
Notice: When pushing a button the background light is activated. After 30 sec.
without further activity the background light goes off and the controller switches
over to the regular operating mode. Not confirmed changes are discarded.
Choosing a colour program
• Push the button [Mode] to activate the modification mode.
The display shows the following:
Select IceBlue
Note: The arrow points to the current
Hard Intern
menu item
Time 002 sec
Run
• The arrow already points to the menu point Program.
• Confirm pushing the button [Set] (arrow blinks=menu point active)
• Use the button [+] or [-] to choose the desired program.
• Push the button [Enter] to confirm your choice.
• To change over to the regular operating mode push the button [Enter] again.
Changing further settings
The basic procedure is the same as choosing a colour program:
• Push the button [Mode] to activate the modification mode.
• Push the button [+] or [-] to choose the desired menu point (pointing arrow).
• Confirm your choice pushing the button [Set] (arrow blinks) to be able to change
the values of the menu point.
• Push the button [+] or [-] to change the value as desired.
• Push the button [Enter] to confirm your changes.
• To change over to the regular operating mode push the button [Enter] again.
Example: The duration of the scenes should be changed from two seconds to
three minutes.
• Push the button [Mode] to activate the modification mode.
• Push the button [+] to get to the menu point time.
• Confirm pushing the button [Set] (arrow blinks).
• Push the button [+] until "003" is displayed.
• Push the button [Enter] to confirm your choice.
• Push the button [+] or [-] to get to the menu point time unit.
• Confirm pushing the button [Set] (arrow blinks).
• Push the button [+]or [-] until "min" is displayed.
• Push the button [Enter] to confirm your choice.
• To change over to the regular operating mode push the button [Enter] again.
2
4
6
3 Menu point Transition
Displays the currently set type
of transition (Soft or Hard)
5 Menu point time:
Displays the duration (001 to
240) of a scene
7 Shows if the program is
running or stopped (Run oder
Stop)
Start/Stop