Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTALLATION
INSTRUCTIONS
GALAXY HET Two-Piece Toilet
1.28 GPF Model 3782-28
Thank you for selecting Crane Plumbing – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must
be as listed below:
A = 12" (305mm)
FINISHED WALL
A
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
Product names listed herein are trademarks of Crane Plumbing
© CRANE PLUMBING 2011
Adjustable Wrench
Flexible Supply Tube
SUPPLY
AS
REQ'D.
FINISHED
FLOOR
WAX RING
Sealant
Closet Bolts
3
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel and slide
into place parallel to wall.
5
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
The Clear Choice
Tape Measure
Carpenters Level
CLOSET FLANGE
A
NUT
CLOSET
BOLT
FLANGE
TAPERED
WASHER
7 3 018 3 0 - 10 0
Tabla de contenido
loading

Resumen de contenidos para Crane Plumbing 3782-28

  • Página 5: Herramientas Y Materiales Recomendados

    Inodoro de dos piezas GALAXY HET 1.28 GPF Modelo 3782-28 Gracias por elegir Crane Plumbing - referente de calidad durante más de 100 años. Para asegurarse de que el producto esté instalado correctamente, por favor lea estas instrucciones cuidadosamente antes de comenzar. (Ciertas instalaciones pueden requerir ayuda profesional.) Asegúrese de que su instalación cumpla con los códigos locales.
  • Página 6 ARANDELA DE GOMA EMPAQUETADURA TORNILLOS DE DE GOMA MONTAJE DEL TANQUE TAPA DE TORNILLO ARANDELA BRIDA DEL INODORO TUERCA INSTALACIÓN DEL TANQUE PERNO DE a. Instale la empaquetadura de goma grande sobre FIJACIÓN la salida roscada en la parte inferior del tanque y ARANDELA TUERCA coloque el tanque sobre la taza, de manera que...
  • Página 7: Cuidado Y Limpieza

    AJUSTES a. Ajuste el nivel del agua. Ésta debe TUBO DE RELLENO TANQUE ajustarse al nivel que indica el tanque PALANCA GANCHO LENGÜETA mediante el ajuste del flotador. Vea el Paso 11 sobre el método de ajuste del nivel del agua VÁLVULA DE FLOTA- SUMINISTRO...
  • Página 8: Guía Para Solucionar Problemas

    GUÍA PARA SOLUCIONAR PROBLEMAS PROBLEMA POSIBLE CAUSA MEDIDA CORRECTIVA No descarga. a. Válvula de suministro del agua cerrada. a. Abra la válvula y deje que el tanque se llene de agua. b. Línea de suministro bloqueada. b. Cierre el suministro de agua, desconecte la línea de suministro e inspeccione todas las empaquetaduras y arandelas.

Tabla de contenido