Axxess TYTO-02 Instrucciones De Instalación
  1. Manuales
  2. Marcas
  3. Axxess Manuales
  4. Interfaces USB
  5. TYTO-02
  6. Instrucciones de instalación
Axxess TYTO-02 Instrucciones De Instalación

Axxess TYTO-02 Instrucciones De Instalación

Interfase amplificada de toyota 2012 y más recientes
Ocultar thumbs Ver también para TYTO-02:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTALLATION INSTRUCTIONS FOR PART TYTO-02
Toyota amplified interface
• Provides accessory power (12-volt 10-amp)
• Used in amplified systems
• High level speaker input
• Retains balance and fade
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
• Micro "B" USB updatable
METRA. The World's best kits.™
TYTO-02
2012-up
FEATURES
APPLICATIONS
See inside front cover
1-800-221-0932
INTERFACE COMPONENTS
• TYTO-02 interface • 16-pin harness with
stripped leads • 14-pin to 10-pin and 28-pin
harness with stripped leads
TOOLS REQUIRED
• Cutting tool • Crimping tool • Tape • Connectors
(example: butt-connectors, bell caps, etc.)
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
metraonline.com
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Tabla de contenido
loading

Manuales relacionados para Axxess TYTO-02

Resumen de contenidos para Axxess TYTO-02

  • Página 1 INSTALLATION INSTRUCTIONS FOR PART TYTO-02 TYTO-02 INTERFACE COMPONENTS • TYTO-02 interface • 16-pin harness with Toyota amplified interface stripped leads • 14-pin to 10-pin and 28-pin harness with stripped leads 2012-up FEATURES TOOLS REQUIRED • Provides accessory power (12-volt 10-amp) • Cutting tool • Crimping tool • Tape • Connectors (example: butt-connectors, bell caps, etc.) • Used in amplified systems • High level speaker input • Retains balance and fade • Prewired ASWC-1 harness included (ASWC-1 sold separately) • Micro “B” USB updatable CAUTION: Metra recommends disconnecting the APPLICATIONS negative battery terminal before beginning any See inside front cover installation.

  • Página 2: Connections To Be Made

    • Connect the Green/Black wire to the radio’s left rear negative speaker output. Sequoia ( 2013-up with NAV) • Connect the Purple wire to the radio’s right rear positive speaker output. Tacoma 2012-up (with NAV) • Connect the Purple/Black wire to the radio’s right rear negative speaker output. Tundra 2014-up (with NAV) Venza 2013-up • Connect the Blue/White wire to the amp turn on wire. (with NAV and without separate display) The following wires on the 16-pin harness will not be used, tape up and disregard: • Red, Brown, Light Green, Blue/Pink, Green/Purple, orange/White. • Connect the 16-pin harness to the TYTO-02.
  • Página 3 TYTO-02 Installing the TYTO-02 Connections to be made From the 10-pin harness, to the aftermarket radio: • With all connections completed to the aftermarket radio, plug the 28-pin and 10-pin harness into the vehicles wiring harness. • Connect the Black wire to the ground wire. • Reconnect the negative battery terminal. • Connect the yellow wire to the battery wire. • Cycle the key, by turning the ignition on for 30 seconds. Then off and on again • Connect the Red wire to the accessory wire. to test the radio. • Connect the orange wire to the illumination wire. Testing the TYTO-02 Note: If the aftermarket radio does not have an illumination wire, tape up and disregard the orange wire. • Turn the ignition on if not already, and then turn the radio on to verify that the • Connect the 14-pin harness to the TYTO-02.

  • Página 4: Important Warning

    INSTALLATION INSTRUCTIONS FOR PART TYTO-02 IMPoRTaNT WaRNING This product includes instructions for installation which must be carefully followed. The instructions are worded in such a manner to assume that the installer is capable of completing these type of electronic installations. If you are unclear as to what you are instructed to do or believe that you do not understand the instructions so as to properly and safely complete the installation you should consult a technician who does have this knowledge and understanding. Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle.

  • Página 5: Interfase Amplificada De Toyota 2012 Y Más Recientes

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA TYTO-02 TYTO-02 COmPOnEnTES dE LA InTERfASE • Interfase TYTO-02 • Arnés de 16 pins con Interfase amplificada de Toyota conectores pelados • Arnés de 14 a 10 pins y 28 pins con conectores pelados 2012 y más recientes...

  • Página 6: Conexiones Que Se Deben Hacer

    • Conecte el cable azul/blanco con el encendido del amp/ antena eléctrica. (con NAV y pantalla independiente) Los siguientes cables del arnés de 16 pins no se usarán, encinte los cables e ignórelos. • Rojo, marrón, verde claro, azul/rosa, verde/púrpura, anaranjado/blanco. • Conecte el arnés de 16 pins con el TYTO-02.

  • Página 7: Instalación Del Tyto

    • Prenda la ignición si no lo ha hecho, y después prenda el radio para probar si • Conecte el arnés de 14 pins con el TYTO-02 funciona. Revise que funcionen bien los controles de balance e intensidad.

  • Página 8: Advertencia Importante

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA TYTO-02 aDVERTENCIa IMPoRTaNTE Este producto incluye instrucciones de instalación que deben seguirse cuidadosamente. Dichas instrucciones están redactadas dando por supuesto que el instalador es capaz de completar estos tipos de instalaciones electrónicas. Si tiene dudas respecto de lo que se le indica que haga o cree que no comprende las instrucciones como para completar la instalación en forma adecuada y segura, debe consultar a un técnico que efectivamente...

Tabla de contenido