Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

C7189U Remote Indoor Sensor
APPLICATION
This indoor sensor is designed to sense temperature
at a remote location and send this information to the
compatible Honeywell Home thermostat. This sensor
can be used as a stand alone sensor or as part of an
averaging network. The thermostat's installer setup
should be modified to tell the thermostat that remote
indoor temperature sensor(s) have been used. If
multiple wired indoor sensors are used, those sensors
are averaged and must be wired as shown in Fig. 6.
Fig. 1. C7189U Remote Indoor Sensor
CAUTION
Electrical Interference (Noise) Hazard.
Can cause erratic system operation.
Keep wiring at least one foot away from large
inductive loads such as motors, line starters,
lighting ballasts and large power distribution
panels.
Use shielded cable to reduce interference
when rerouting is not possible.
M24055A
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
Operating Ambient Temperature Range:
45 to 88 °F (7.2 to 32 °C).
Display Range:
0 to 99 °F (-18 to 37 °C).
Sensor Accuracy:
+/-1.5 °F at 70 °F (+/-0.84 °C at 21 °C)
Operating Relative Humidity:
5 to 95% non-condensing.
Finish:
White.
Resistance Characteristics:
Negative temperature coefficient (NTC). Resistance
decreases as the temperature increases.
Dimensions in inches (mm):
1 1/2 (38) wide x 2 1/4 (57) high x 3/4 (19) deep.
Distance:
Maximum distance between thermostat and sensor is
200 feet.
Must be installed by a trained,
experienced technician
• Read these instructions carefully. Failure to follow
these instructions can damage the product or
cause a hazardous condition.
• Check the specification in this booklet to verify
that this product is suitable for the application.
• Always test for proper operation after installation.
69-1710EFS-04
Tabla de contenido
loading

Resumen de contenidos para Honeywell Home C7189U

  • Página 9: Sensor Remoto Para Interiores

    Distancia: La distancia máxima que puede haber entre el M24055A termostato y el sensor es de 200 pies. Fig. 1. Sensor remoto para interiores C7189U Este producto debe ser instalado PRECAUCIÓN por un técnico experto debidamente entrenado. Riesgo de interferencia eléctrica (ruido).
  • Página 10: Consejos Para La Instalación

    5 FEET (1.5 METERS) M24115A Fig. 2. Ubicación típica para el sensor C7189U. Instalación de la placa para pared del sensor remoto Quite la cubierta del sensor remoto como se muestra en la Fig. 3. 1. Pase los cables a través el agujero para cables.
  • Página 11 CONFIGURACIÓN PARA QUE OPEREN CORRECTAMENTE. LOS ALAMBRES DEBEN TENER UN CABLE POR SEPARADO DEL CABLE DEL TERMOSTATO. MS19973 Fig. 6. Cableado para sensores C7189U múltiples. FUENTE DE ALIMENTACIÓN. PROPORCIONE MEDIOS DE DESCONEXIÓN Y PROTECCIÓN CONTRA SOBRECARGAS SEGÚN SE REQUIERA. SI SE REQUIERE MÁS DE UN SENSOR REMOTO C7189, CONSULTE LA FIGURA 6.
  • Página 12: Funcionamiento

    69-1710EFS—04 M.S. Rev. 03-19 | Impreso en EE. UU. Este producto es fabricado por Resideo Technologies, Inc., Golden Valley, MN, 1-800-633-3991 ©2019 Resideo Technologies, Inc. La marca comercial Honeywell Home se utiliza en virtud de la licencia emitida por Honeywell International Inc. Todos los derechos reservados.

Tabla de contenido