Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Fastener Kit: 36509F
Equipment Required: N/A
Wrenches: 14mm, 17mm, ¾ or 7/8
1 2 3 4
1 1 1 1
Qty. (2)
Block .250 x 1.50 x 4.00 (2 square holes)
2 2 2 2
Qty. (4)
Carriage bolt ½-13 x 4.50 Long Gr5
3 3 3 3
Qty. (4)
1/2 Conical washer
4 4 4 4
Qty. (4)
Hex nut ½-13
1.
Remove (3) bolts and factory tow loop from passenger's side frame rail. Return bolts and tow loop to vehicle owner..
2.
Insert carriage bolts and blocks into existing holes in the side of frame rails. Adjust carriage bolts to be flush with inside of frame rails.
Note: On the driver's side, the carriage bolts are installed by reaching between the bumper fascia and over the top the carbon canister.
3.
Raise the hitch into position and push the carriage bolts through the holes in hitch. Loosely install the ½ conical washers and hex nuts onto
carriage bolts.
Tip: For ease of installation, raise the driver's side of hitch first, guiding the flange on side bracket around the carbon canister. Then raise
the passenger's side into position.
4.
Loosely install the M10 hex bolts with 7/16 conical washers into existing weld nuts in the bottom of frame rails.
5.
First, tighten the ½-13 GR5 carriage bolts to specifications.
6.
Then, tighten the M10 CL8.8 bolts to specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2011,2014,2015 Cequent Performance Products, Inc - Printed in Mexico
Installation Instructions
Mitsubishi Outlander Sport / RVR
Fascia Bumper
(Sold separately)
Drawbar Kit:
36051
Drawbar must be used in the
Rise position only.
Frame rail
5 6
Figure 1
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M10-1.25 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
3500 Lb. (1589 kg) Max Gross Trailer Weight
300 Lb. (136 kg) Max Tongue Weight
Wiring Access Location: SUV 1, SUV 2
5 5 5 5
Qty. (2)
Bolt M10 x 1.25 x 30mm CL8.8
6 6 6 6
Qty. (2)
7/16 Conical Washer
Sheet 1 of 3
36509N
Part Numbers:
36509
90210
06131
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Fasteners typical
both sides
Factory Tow Loop
10-13-15
Form F206 Rev A 5605
Rev. C
Manuales relacionados para Cequent Performance Products 36509
Resumen de contenidos para Cequent Performance Products 36509
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2011,2014,2015 Cequent Performance Products, Inc - Printed in Mexico Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. z2011,2014,2015 Cequent Performance Products, Inc. -Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 36509N 10-13-15 Rev. C ©2011,2014,2015 Cequent Performance Products, Inc. Impreso en México Form F206 Rev A 5605...