Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Fascia
Vehicle Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36455F
Wrenches: 13mm, 15mm, 18mm
Drill Bits: None
Existing M12 Bolt
Existing M10 Bolt
Note: Uses all existing
Bolts on Vehicle
1.
Lower exhaust by removing bolt which attaches rearmost hanger bracket to passenger's side frame rail. Retain bolt for
reinstallation.
2.
Snap plastic loom in place over Air Conditioning line on Passenger's side near bolt if present. See Figure 2 above.
3.
Remove existing bolts from frame rails as shown in Figure 2, (2) on driver's side, (2) on passenger's side and retain for hitch
installation.
4.
Raise hitch into position as shown in Figure 1 and attach with existing bolts removed in step 2. Hand tighten.
5.
Push hitch towards driver's side, so that passenger's side bracket is up against trunk pan, and tighten fasteners to
specifications below.
6.
Raise exhaust back into position and reinstall bolt removed in step 1.
Note: Rotating exhaust hanger bracket before tightening will add clearance between side bracket and exhaust.
Tighten all M10 CL10.9 fasteners with torque wrench to 53 Lb.-Ft. (72 N*M)
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2007, 2008, 2009, 2014,2015 Cequent Performance Products
Installation Instructions
Chrysler Town & Country
Dodge Grand Caravan
RAM C/V Tradesman
(Sold separately)
Drawbar Kit:
36061
Drawbar must be
used in the Rise
position only.
Existing
weldnuts
Figure 1
Figure 1
VW Routan
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Driver's Side
Frame Rail
Remove
Bolts
Sheet 1 of 3
Printed in Mexico
Part Numbers:
UHI 36332
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
3500 (1589 Kg.)
Leave these bolts in
Vehicle Forward
Figure 2
Plastic loom,
magnified view
Attention:
On some vehicles
air-conditioning lines
are very close to this
attachment. Be careful
not to damage lines when
installing hitch.
Existing M12 Bolt
Existing M10 Bolt
36455N
10-13-15
Form: F205 Rev A 5-6-05
36455
90169
06550
Max Tongue
WT (LB)
300 (136 Kg.)
Passenger's
Side Frame
Rail
A.C. line,
some models
Remove
Bolts
Dev. G
Manuales relacionados para Cequent Performance Products 36455
Resumen de contenidos para Cequent Performance Products 36455
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2007, 2008, 2009, 2014,2015 Cequent Performance Products Sheet 1 of 3 36455N 10-13-15 Dev.
- Página 2 V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36455N 10-13-15 Rev. G z 2007, 2008, 2009, 2014,2015 Cequent Performance Products Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. z 2007, 2008, 2009, 2014, 2015 Cequent Performance Products Hoja 3 de 3...