Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Vehicle forward
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75912F
Wrenches: 15mm, 3/4
Drill Bits: None
Slowly start the first few
threads keeping the bolt
perpendicular to the frame rail.
Self-tapping bolts method
j
Qty. (2)
Carriage bolt 1/2-13 X 1.50 GR5
k
Qty. (2)
Spacer .25 X 1.00 X 3.00
l
Conical washer 1/2"
Qty. (2)
1.
Start by threading the self-tapping bolts (item 5) into the locations, as shown in illustration above. The bolts have a self-aligning
feature. Start the first few threads slowly keeping them perpendicular to the frame rail. Thread the bolt ½ way or more into the
frame rail, then remove the bolt to be reinstalled later.
2.
Feed the coiled end of the pull wire through the forward slot in the frame rail and out the open end of frame rail. Attached carriage
bolt and spacer to the pull wire. Pull the pull wire with fasteners into location though the forward hole. Leave pull wires attached.
3.
Raise hitch into position feeding the pull wires through the adjacent slots on the hitch. Feed conical washer over pull wire, using
the washer to hold the bolt in place remove the pull wires and attach the hex nut. Tighten to hold hitch in place, repeat on
opposite frame rail.
4.
Re-install the self-tapping bolts. Once all bolts are in place center hitch on vehicle and tighten.
5.
Torque all fasteners to specifications below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014 Cequent Performance Products, Inc
Installation Instructions
Bumper
Frame rail open for
access for carriage
bolt and spacer.
Frame rail
n
Tighten all fasteners M12 X 1.75 with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all fasteners ½-13 Gr 5 with torque wrench to 75 Lb.-Ft. (102 N*M)
Ford Transit
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: XXX
Note: Fasteners typical
Self-tapping bolts locations
m
Qty. (2)
Hex nut 1/2-13
n
Qty. (4)
Self-tapping bolt M12 X 1.75 X 40
o
Pull wire 1/2"
Qty. (2)
Sheet 1 of 3
75912N
Printed in Mexico
Part Numbers:
78501 UH
Max Gross
Trailer WT (LB)
8000 (3632 Kg)
5000 (2270 Kg)
Accessory Rating
both sides
n
o
9-11-14
Form: F205 Rev C 9-17-2012
75912
87671
44719
Max Tongue
WT (LB)
800 (363 Kg)
750 (341 Kg)
E
j
k
l
m
Rev. B
Manuales relacionados para Cequent Performance Products 75912
Resumen de contenidos para Cequent Performance Products 75912
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2014 Cequent Performance Products, Inc Sheet 1 of 3 75912N 9-11-14 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2014 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2014 Cequent Performance Products, Inc Hoja 3 de 3 75912N 9-11-14 Rev.