Cequent Performance Products 60298 Instrucciones De Instalación

Vehicle Frame
Vehicle Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 60298F
Wrenches/Sockets: 13mm, 11/16
Drill Bits: None
Other Tools: Socket extension, Tin
Snips or a tool to cut aluminum heat
shield.
How to Fish-wire
Insert large coiled end of
Bolt Leader through
attachment hole in bottom
of frame and out through
large access hole. Insert
coiled end through block
and screw on to bolt. You
are now ready to pull
assembly through frame
and leave ends of Bolt
Leaders sticking out a
couple of inches.
Carriage Bolt, 7/16"-14 x 1-1/2", Gr. 5
Qty. (4)
1
Block, 15/16" wide by 3" long, with offset square hole
Qty. (4)
2
Conical Toothed Washer, 7/16"
Qty. (4)
3
Remove (3) rubber exhaust isolators, (2) on Driver's side and (1) on Passenger side to allow exhaust to drop down and rest on
1.
rear axle. Use 13mm wrench to remove metal bracket holding rubber isolator rearward on Driver's side. See Picture 1, 2 & 3
next page.
Heat shield needs to be trimmed on driver's side above muffler. See Picture 4 next page for cutting information. Make sure
2.
trimmed heat shield is securely attached back to vehicle before proceeding with hitch installation.
3. Fish-wire carriage bolts with blocks up through large round access holes in bottom of frame forward of attachment holes, and
out through attachment holes in bottom of vehicle frame, both sides of vehicle. See Picture 5 next page.
4. Raise hitch into place above muffler. Be careful not to push bolts installed in Step 3. back up in to frame. Locate hitch frame
brackets on bottom of frame, being careful to guide bolt leader wire ends through holes in hitch brackets.
5. Pull ends of carriage bolts through vehicle frame and hitch brackets and loosely install conical toothed washers and hex nuts.
Make sure carriage bolts engage with square hole in block as you pull bolts through frame.
6. Pull hitch rearward as far as possible. This will allow enough clearance for spare tire basket to drop down and clear the hitch
cross tube if the spare tire needs to be removed later.
7. Now you can tighten nuts for the carriage bolts holding hitch to vehicle frame to specification below.
8. Reinstall exhaust hangers removed in Step 1.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2012 Cequent Performance Products
Installation Instructions
Chevrolet Orlando
Drawbar Kit:
3593
1
2
3
4
Tighten 7/16"-Gr.5 Carriage Bolts with torque wrench to 50 Lb.-Ft. (68 N*M)
All models
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Fasteners typical,
both sides of vehicle.
3
4
Vehicle frames
cut-away to
show detail
Hex Nut, 7/16" Grade 2
Qty. (4)
4
7/16" Bolt Leaders
Qty. (4)
5
Another fine Cequent Performance Products hitch
Sheet 1 of 6 60298N
Part Numbers:
60298, 24881, 77268
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Wiring Access Location: SUV3, SUV4
This is a magnified
view of a Bolt Leader
Large access hole in
bottom of frame for
fish-wiring bolts
with blocks.
5
2
5
2-7-12
1
Rev. B