Westin Automotive Products 27-1755 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
SURE-GRIP
MOUNT KIT
BOARDS
EQUIPO DE MONTAJE
27-6140
JEU DE MONTAGE
27-6145
27-1755
27-6540
SURE-GRIP
OPTIONAL LIGHT KIT
27-6000
ITEM QTY
CONTENTS -
1 2 STEP BOARD (PURCHASED SEPARATELY)
2 5 MOUNT BRACKET
3 1 THIN MOUNT BRACKET (FOR USE WITH DIESELS WITH UREA TANK)
4 12 M8-1.25 X 30MM HEX HEAD BOLT
5 6 M8-1.25 HEX NUT
6 2 M8-1.25 EXTRUDED U-NUT
7 12 5/16-18 X .75 SQUARE HEAD BOLT
8 30 5/16" FLAT WASHER
9 12 5/16" LOCK WASHER
10 12 5/16" LOCK NUT
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2 5 SOPORTES DE MONTAJE
3 1 DELGADA DEL MONTAJE DE SOPORTE (PARA USAR TANQUE DE UREA)
4 12 PERNOS CON CABEZA HEXAGONAL M8-1.25 X 30MM
5 6 TUERCAS HEXAGONALES DE M8-1.25
6 2 TUERCA A PRESIÓN EN "U" M8-1.25
7 12 PERNOS CON CUADRADA DE 5/16-18 X .75
8 30 ARANDELAS PLANAS DE 5/16"
9 12 ARANDELAS DE PRESIÓN DE 5/16"
10 12 TUERCA A PRESIÓN 5/16"
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2 5 SUPPORTS DE MONTAGE
3 1 MINCEPOUR MONTAGE MURLl (POUR UNE UTILISATION AVEC UREE)
4 12 BOULONS A TETE HEXAGONALE M8-1.25 X 30MM
5 6 ÉCROUS HEXAGONAUX M8-1.25
6 2 ECROU EN U EXTRUDE M8-1.25
7 12 BOULONS A TETE CARREE 5/16-18 X .75PO
8 30 RONDELLE PLATE 5/16 PO
9 12 RONDELLES A FREIN 5/16 PO
10 12 ECROU FREINE 5/16 PO
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is
strongly recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Attach mounting brackets as shown. SEE FIGURE 7 AND 8. FOR LATE MODEL DIESEL TRUCKS SEE PG. 4 FOR THE FRONT PASSENGER
SIDE MOUNTING BRACKET
STEP 3. Insert square head bolts as shown (3 per slot, 6 per Step Board/Running Board). SEE FIGURES 2 AND 3.
NOTE: For lighted boards, run wiring harness prior to attaching board to brackets (refer to Step 3). SEE FIGURES 3 AND 5. Run longer
wire harness on passenger side.
STEP 4. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip
Running Board as shown. SEE FIGURE 1. Drill hole through plastic strip and run wires as shown. SEE FIGURE 4.
STEP 5. Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque
values are 10 FT.LBS. for 5/16" square head fasteners and 23 FT.LBS. for 8MM fasteners. SEE FIGURE 5.
NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A
PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN
SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH
WEATHER.
HINT: Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and blue wires going
into rear sockets, should be inserted and recessed about 1/4". NOTE: Remove bulbs and apply white grease into sockets and replace
bulbs. Apply RTV Silicone where lights go into socket. Install lights and run wire loom as shown. SEE FIGURE 3. For Sure-Grip
Running Boards, run wire loom down center as shown. SEE FIGURE 2.
STEP 6. Determine whether your vehicle has a positive or negative switching courtesy system or an auxiliary light source (most Fords). Obtain
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-13 CHEVY SILVERADO/ GMC SIERRA 1500 SERIES CREW CAB
APLICACIÓN: CHEVY SILVERADO MC SIERRA 1500 CREW CAB, MOD. 2007-13
APPLICATION: CHEVY SILVERADO/GMC SIERRA 1500 CREW CAB 2007-13
MOLDED
STEP
BOARDS
27-0020
27-0025
1
CONTENIDO - CONTENU
/G
2
TOOLS-HERRAMIENTA
13MM SOCKET
13MM WRENCH
1/2" SOCKET
RATCHET
TORQUE WRENCH
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
DADO DE 1/2"
MANERAL
LLAVE DE TORQUE
DOUILLE 13MM
CLÉ 13MM
DOUILLE 1/2 PO
CLIQUET
ClÉ DE COUPLE
W13-0996 75-0768 REVISION F 4/2/13
3
-OUTILS