1.
Getting to know your device
Maximum load for the outlet: 600W incandescent, 1800W
(15A) resistive, or 1/2 HP motor
One Zigbee-controlled grounded outlet for lighting and
•
small appliances
Remote ON/OFF control through your Control4 system
•
Manual ON/OFF control with the front panel push button
•
Over-the-air updates—Once joined to your Control4
•
Zigbee network, the Outdoor Plug-In Outlet Switch can
transparently receive updates through your Control4
controller
LED status indicator—Programmable, single-color LED
•
Grounded 3-wire power connection for safety
•
Weather- and impact-resistant housing; suitable for
•
outdoors in wet or damp conditions
4.
A One controllable grounded outlet for lighting and small
appliances
B Status LED
Programmable, single-color LED
C Program/Manual button
Single press —turn ON/OFF
C
B
A
`
2.
IMPORTANT!
This outdoor switch is suitable for outdoor use in damp locations. Do not immerse in water. Install at least 1 m (3 ft)
above ground level with the receptacle pointed down. When used outdoors, plug the outdoor switch into a GFCI outlet
with a receptacle cover rated for outdoor use.
At least 1 m (3 ft) off the ground
>1 m
Two mounting tabs with screw keyholes are located on the top of the outdoor switch.
Install the screws in the desired location leaving 3/16" of the screw showing. Align the mounting tab with the screw heads.
Slide the tabs over the screws and push the outdoor switch down into place.
5.
Note: Requires OS 3.1.2 or newer.
1. Plug the load you plan to control into the outlet on the
Outdoor Plug-In Outlet Switch.
2. Plug the outlet switch into an available outlet.
Note: Plug directly into outlet. Do not use with extension
cords.
3. In Composer, add the driver for the Outdoor Plug-In Outlet
Switch (C4-V-OOSW120) to the project.
4. In the Network > Zigbee Network view, double-click the
driver for the outlet switch to open the Identify window.
5. Follow Composer's on-screen instructions to identify the
outlet switch; press the switch's Program button 4 times.
6. After the outdoor switch is joined to the Zigbee network, the
LED status indicator stops blinking, and the address for the
outdoor switch appears in Composer. The outdoor switch is
now paired to the Zigbee network and can be controlled.
Plug into a GFCI outlet
Note: The LED blinks slowly until the switch is added to
a Control4 project.
Note: If the switch does not successfully join the
network, the auto-scan process will eventually time out
(and the LED status indicator will stop blinking rapidly).
To restart the pairing process following a timeout, press
the top button 4 times quickly.
If prompted to enter the install code, refer to the QR
code label on the product. Enter the full code.
Example:
EUI: 000D6FFFFECD6DD6
Install code: 39F9-0CA3-09F2-4C6F-
8080-131B-6EE4-1E95-D22E
3.
NOTE: Plug the load directly into the outdoor switch.
Do not use with extension cords.
The Program/Manual button on the outdoor switch
allows the user to:
Turn the connected equipment ON/OFF. If the
outdoor switch is OFF, press the button once to
turn it ON and once to turn OFF.
6.
Remove from Zigbee network
(Reset Outdoor Plug-In Outlet Switch)
From Composer
In Composer under Network > Zigbee Network, select the
Outdoor Plug-In Outlet Switch and click on Disconnect. The
outlet switch will be removed from the Zigbee network. All
configuration parameters will be reset after the outlet switch
is removed from the network.
Manual Reset
To manually reset and remove the Outdoor Plug-In Outlet
Switch from the Zigbee network, press the Program/Manual
button 13 times quickly (short presses).
