Tabla de contenido
Idiomas disponibles
Idiomas disponibles
RADIOS AND ANTENNAS
The nMAP2 access point has two radios and an integral antenna array.
The default and available operation for each radio are:
Radio Default Mode
1
Operating mode:
Operating Modes:
Access Point
Client
Ad-Hoc
802.11s
Pseudo Ad-Hoc (ahdemo)
Monitor
Access Point (WDS)
Client (WDS)
Wireless mode:
Wireless modes:
802.11ac
802.11b (not compatible with antenna)
802.11g (not compatible with antenna)
802.11a
802.11g+n (not compatible with antenna)
802.11a+n
2
Operating mode:
Operating Modes:
Access Point
Client
Ad-Hoc
802.11s
Pseudo Ad-Hoc (ahdemo)
Monitor
Access Point (WDS)
Client (WDS)
Wireless mode:
Wireless Modes:
802.11g+n
802.11b
802.11g
802.11g+n
802.11a+n (not compatible with antenna)
802.11ac (not compatible with antenna)
* Choices may be limited by Country selected during setup.
RESET OPERATION
Reset lines are available in connector J1. Momentary connection of
pins 13 and 14 reboots the nMAP2 access point (WLAN1 and WLAN2
indicators flash in unison, one flash per second for approximately one
minute). Holding connection until WLAN1 and WLAN2 indicators flash
alternately at one flash per second resets the nMAP2 to the factory
default settings. Reset lines are not connected in aircraft installation.
Other Choices*
DISCRETE INPUTS
Two discrete inputs accessed via connector J1 enable remote on/off
(power supply enable) and RF on/RF off (RF enable) control. Inputs
must be connected to signal ground to power up and enable RF.
ETHERNET PORTS
The nMAP2 access point has three auto sensing 10/100/1000 Base-T
Ethernet ports accessed via connectors J2 and J3.
INTERFACE CONNECTORS
Connector J1 provides connection for input power, discrete signals, and
IP address selection. (See nMAP2 Operator's Manual M365-769 for IP
address selection wiring.)
Pin*
Signal
1
IP Strap 0
2
IP Strap 1
3
IP Strap 2
4
IP Strap 3
5
Power Supply Enable
6
IP Strap 0 Ground
7
IP Strap 1 Ground
8
IP Strap 2 Ground
9
IP Strap 3 Ground
10
RF Enable
* Use Deutsch shell DMC-MD 20A, insert & contacts DMC M 20-22SN,
backshell 787-8055-13M or equivalent for mating connector.
Connector J2 provides connection for Ethernet port 2 and power out.
Pin*
Signal
1
Port 2 Bidirectional Pair A+
2
Port 2 Bidirectional Pair B+
3
Port 2 A/B Inner Shield
4
Port 2 Bidirectional Pair C+
5
Port 2 Bidirectional Pair D+
6
Port 2 Bidirectional Pair B-
7
Port 2 Bidirectional Pair A-
8
Port 2 C/D Inner Shield
9
Port 2 Bidirectional Pair D-
10
Port 2 Bidirectional Pair C-
* Use Deutsch shell DMC-MD 20B, insert & contacts DMC-M 20-22PN,
backshell 787-8055-13M or equivalent for mating connector.
2
Pin*
Signal
11
No connection
12
No connection
13
Reset (not used on aircraft)
14
Signal Ground
15
28 VDC Positive (Primary)
16
115 VAC Line (Hot)
17
No connection
18
115 VAC Neutral
19
Chassis Ground
20
28 VDC Return
Pin*
Signal
11
No connection
12
No connection
13
No connection
14
No connection
15
No connection
16
No connection
17
No connection
18
No connection
19
No connection
20
No connection
Tabla de contenido
