Care And Cleaning; Troubleshooting - ETI ST-8-90-840-SV-N Guía De Uso Y Cuidado

care anD cleanIng

CaUTiON: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning
the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals,
solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.

troublesHootIng

Minor problems often can be fixed without the help of an electrician.
WarNiNG: Before doing any work on the fixture, disconnect power to the light fixture.
Problem
The fixture will not light.
The fuse blows or the
circuit breaker trips when
the light is turned on.
WarNiNG: Carefully read and understand the information given in this manual before beginning the assembly and
installation. Failure to do so so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
• Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• This product must be installed in accordance with the applicable installation codes by a person familiar with the
construction and operation of the product and the hazards involved. • Risk of electrical shock. To reduce the possibility of
serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
NOTiCe: Suitable for operation in ambient temperatures not exceeding 113°F/45°C.
NOTiCe: Suitable for damp locations.
NOTiCe: Do not use this fixture with a dimmer switch.
NOTiCe: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and
the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult
the dealer or an experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
warrantY
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and
workmanship. If this product should fail to operate due to defects in material or workmanship within 60 months of purchase, see
www.ETiSSL.com for details. This product will be repaired or replaced, at ETi's option. This warranty is expressly limited to repair
or replacement of product and liability for direct, incidental, or consequential damages is hereby expressly excluded. Some
states do not allow exclusions of direct, incidental or consequential damages, so the above limitation of exclusion may not apply
to you. This warranty gives the consumer specific legal rights, which vary from state to state. WARRANTY IS VOID IF PRODUCT IS
NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.
Possible cause
The power is off.
The circuit breaker is off.
There is a bad connection.
There is a defective switch.
The wires are crossed or the
power wire is grounding out.
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-sslI (1-855-384-7754)
solution
Ensure the power supply is on.
Ensure the circuit breaker is in the on position.
Check to ensure proper wire connections are made. Contact a
qualified electrician.
Contact a qualified electrician.
Check the wire connections. Contact a qualified electrician or call
customer service 1-855-384-7754.
www.etissl.com