Silca Air4 V 64 Manual De Instrucciones página 8

Air
ENGLISH
4
ATTENTION: before copying make sure the original remote control is working properly.Check the
state of the battery.
COPY FIXED CODES :
1.
Press and hold down button 1 on the "Air4 V 64-Air4 V Plus 128 " remote control and at
2.
the same time press button 4 four times. Release both buttons: the "Air4 V 64-Air4 V Plus
3.
128 "remote control LED will flash briefly about every 2 sec. Place the remote control to be
4.
cloned in front of the "Air4 V 64-Air4 V Plus 128 ", at a distance of about 2 centimetres. Press
and hold down the button to be copied from the original remote control and wait for the "Air4
V 64-Air4 V Plus 128 "LED to start flashing rapidly, which confirms that the code has been
5.
acquired. This operation may take a few seconds. While the LED is flashing, press the "Air4 V
64-Air4 V Plus 128 "button to which the code must be transferred and hold down until the LED
goes out.
N.B. •If the LED goes out unexpectedly it means the code has not been acquired. Repeat the
operation from point 1.• To programme the second "Air4 V 64-Air4 V Plus 128 "button, repeat
the operation from point 1.
COPY ROLLING CODE NORMAL* :Follow the "Fixed Code" instructions.
COPY ROLLING SECURE LEARNING* :
1.
Press and hold down button 1 on the "Air4 V 64-Air4 V Plus 128 "and at the same time press
button 4 four times. 2. Release both buttons: the "Air4 V 64-Air4 V Plus 128 "LED will flash brie-
fly about every 2 sec. 3. Place the remote control to be cloned in front of the "Air4 V 64-Air4 V
Plus 128 ", at a distance of about 2 centimetres. 4. Press and hold down the button to be copied
from the original remote control and wait for the "Air4 V 64-Air4 V Plus 128 "LED to go on
5.
without flashing and then start double flashing about every 2 seconds. Transmit the original
remote control source code (check the website www.silca.biz to find the one for the remote
6.
control you want to copy). The "Air4 V 64-Air4 V Plus 128 "LED will flash rapidly; press the
button by which the code will be memorised and hold down until the LED goes out.
(*) Full list of original models at: www.silca.biz.
N.B.: Transmit the source code to copy an "Air4 V 64-Air4 V Plus 128 "remote control program-
med as "Rolling Secure Learning".
PROCEDURE A.L.S.:Simplified procedure to activate the remote control on the receiver. The list
of receivers compatible with the procedure can be found on www.silca.biz. For other receivers
see the original instructions provided by the manufacturer.
N.B.:Follow A.L.S. procedure before using the original remote control.
1.Stand close to the automation 2.Hold down the programme button for about 10 seconds;
release when the LED starts to flash 3.Wait until the LED goes out.
ATTENTION : receivers may have the radio channel disabled. In such cases enter the new re-
mote controls using a manual procedure.
TRANSMISSION OF "Air4 V 64-Air4 V Plus 128 " SOURCE CODE :
1.Press buttons 1 and 2 on the remote control simultaneously for 8 seconds and release when
the LED flashes. 2.While the LED is flashing press the button for which the source code is requi-
red.
Battery replacement:
Use a star screwdriver to loosen the screw on the back of the "Air4 V 64-Air4 V Plus 128
"remote control.The "Air4 V 64-Air4 V Plus 128 "remote control is powered by a 3V CR2032 LITHIUM BATTERY.
Check polarity-Do not throw flat batteries away: dispose of them in the special waste sorting centres.
8 Copyright Silca S.p.A 2020