Manuales relacionados para Helios FMXL75
Resumen de contenidos para Helios FMXL75
- Página 1 FMXL75 G INFORMATION s below show the Extra Large Full Motion Mount attached to the left of the corner. Depending on the desired angle for viewing, please • Please read these instructions carefully before using. o determine which wall to mount your panel.
- Página 2 MW PRODUCTS no ofrece ninguna garantía, ni expresa ni implícita, respecto de la información aquí incluida. MW PRODUCTS no se responsabiliza de la precisión de la información provista en este documento, ni tampoco de que sea completa o suficiente. FMXL75 Information Soportes de pared ADVERTENCIA: NO LEER, ENTENDER CABALMENTE Y SEGUIR TODAS LAS INSTRUCCIONES PUEDE DERIVAR EN LESIONES GRAVES, DAÑOS MATERIALES O LA NULIDAD DE LA...
-
Página 3: Safety Warning
STEEL M6 X 5/8” ALLEN WASHER 10mm ACORN WRENCH WASHER WRENCH SPACER 8 mm LAG 5 mm ANCHOR BOLT PRODUCT COMPONENT PARTS Flat Panel Mounting Pattern (W x H) Minimum: 200mm x 100mm Maximum: 700mm x 500mm Product Components Contents Description Wall Bracket Universal Monitor Bracket... - Página 4 Do not use this product for any purpose not explicitly specified by Metra Home Theater Group™. Metra Home Theater Group™ cannot be liable for damage or injury caused by incorrect assembly, or incorrect use. • Read these instructions. • Keep these instructions. •...
- Página 5 STEP 1A- FLAT BACK FLAT PANEL (UNIVERSAL MONITOR PLATE) Connect Universal Monitor Plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur SQUARE WASHER STEP 1B- CURVED BACK FLAT PANEL (UNIVERSAL MONITOR PLATE) Connect Universal Monitor Plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur SQUARE...
- Página 6 STEP 1- USE M8 STEEL WASHER IF THE PHILLIPS SCREWS FROM THE MONITOR KIT ARE TOO LONG Diagrams show three options for using additional washers if hardware screws are too long to properly tighten into back of flat panel television. STEP 2- CENTER UNIVERSAL MONITOR PLATE Monitor Plate must be centered (horizontal plane) on back of flat panel STEP 2- SECURE UNIVERSAL MONITOR PLATE VERTICAL RAILS...
- Página 7 STEP 2C- PRIOR TO EXTENDING ARMS REMOVE ARM ASSEMBLY FROM WALL PLATE Prior to extending arm： Remove 2 Allen screws at top of Arm Assembly with included Allen wrench. Remove 2 Allen screws at bottom of Arm Assembly with included Allen wrench.
- Página 8 STEP 3A- WOOD STUD INSTALLATION (CONCRETE INSTALLATION SKIP TO 3B) Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre. LEVEL WALL PLATE DRILL BIT WITH INCLUDED...
- Página 9 STEP 3B – SOLID CONCRETE INSTALLATION Solid Concrete Drill Bit Level Drill pilot hole Concreto sólido S. broca Nivelado Realice el agujero piloto Béton massif Foret Level Percez le trou de guidage DRILL BIT LEVEL WALL PLATE NOT INCLUDED WITH INCLUDED BUBBLE LEVEL AND MARK HOLES FOR DRILL BIT PILOT HOLE...
- Página 10 STEP 4 - ATTACH ARM ASSEMBLY TO WALL BRACKET Position Arm Assembly to desired lateral position on wall bracket for opti- mum placement of Flat Panel. Secure Arm Assembly to Wall plate using screws removed from Step 2. STEP 5 - ATTACH UNIVERSAL MOUNT BRACKET TO ARM ASSEMBLY & WALL BRACKET Heavy, Assistance Required TRES LOURD ! Cette etape...
- Página 11 SECURE MONITOR PLATE TO ARM ASSEMBLY Secure Acorn Nut and Washer on Monitor Plate to Arm Assembly M6 Wrench M6 Washer M6 Acorn Nut ADJUST TILT TENSION/ POST INSTALLATION LEVEL Built-in level feature for post installation Adjust tilt mechanism tension with ratchet handle lever correction Rotate ratchet...
-
Página 12: Warranty Information
To obtain warranty service, contact Helios customer service at 1-866-839-9187. You must supply a copy of your original receipt. If your product must be shipped to Helios for inspection, you will be responsible for the shipping charges. Replacement product shipped to you will be returned freight pre-paid.