Idiomas disponibles
Idiomas disponibles
READ
INSTRUCTIONS
IN
WITH THE ILLUSTRATIONS
IMPORTANT
1.THE FAN MUST BE SITED AND CONNECTED
IN
ACCORDANCE
WITH
REGULATIONS (UK) OR THE APPROPRIATE
STANDARDS IN YOUR COUNTRY.
2.THIS APPLIANCE IS NOT SUITABLE FOR
INSTALLATION IN A SHOWER CUBICLE OR
ENCLOSURE AND MUST BE SITED AWAY FROM
ANY SOURCE OF WATER SPRAY, AND MUST BE
OUT OF REACH OF A PERSON USING A FIXED
BATH OR SHOWER.
3.SITE AWAY FROM DIRECT SOURCES OF
HEAT IN EXCESS OF 50ºC.
4.WHEN THE FAN IS INSTALLED IN A ROOM
CONTAINING A FUEL BURNING APPLIANCE,
THE INSTALLER MUST ENSURE THAT AIR
REPLACEMENT IS ADEQUATE FOR BOTH THE
FAN AND THE FUEL BURNING APPLIANCE. IF
THE FAN CAN BE USED TO SUPPLY AIR INTO
THE ROOM THE INSTALLER MUST ENSURE
THAT THE FAN INTAKE IS LOCATED AT LEAST
600mm AWAY FROM ANY FLUE OUTLET.
5.WIRING SHOULD BE VIA A SWITCHED SPUR
WITH A 3 AMP FUSE (UK ONLY).
6.DOUBLE POLE SWITCH OR PLUG AND
SOCKET SHOULD BE LOCATED OUTSIDE THE
ROOM
CONTAINING
A
FIXED
SHOWER.
7.THIS APPLIANCE MUST BE EARTHED.
8.READ THESE INSTRUCTIONS FULLY BEFORE
COMMENCING INSTALLATION.
9.IF A T-SERIES CONTROLLER IS TO BE USED,
IT IS ESSENTIAL TO WIRE WITH 5-CORE
CABLE.
10.THE APPLIANCE IS NOT INTENDED FOR
USE
BY
YOUNG
CHILDREN
PERSONS WITHOUT SUPERVISION.
11.YOUNG
CHILDREN
SUPERVISED TO ENSURE THAT THEY DO NOT
PLAY WITH THE APPLIANCE.
(Note:- Darkroom and in-line models are variants of
these models)
VOLTAGE
A.Check rating label to ensure that the motor is the
correct voltage (see A)
WHERE TO FIT
BA short circuit of the air flow should always be
avoided by siting the fan as far away as possible from
and opposite to the main source of air replacement.
FAN DIMENSIONS
Before commencing work, study the tables shown in
figures C1/C2, to ensure fan will fit in position
proposed.
NB: Allow a minimum of 54mm above fan casing for
withdrawal of connector socket.
THICKNESS OF GLASS
Fans can be fitted in most types of glass and fixing
thickness up to 32mm, with the screws provided. When
fixing thickness exceeds 32mm, the unit should be
secured with Extended Fixing Rods. If the unit is to be
installed in a location exposed to severe wind
turbulence or in non-vertical panes, thicker glass will be
required – consult your nearest Vent-Axia Sales,
Service and Distribution Centre.
DFor minimum thickness of glass, for normal
conditions, see fig. D.
PREPARATION FOR INSTALLATION
Dismantling
E1Place fan unit, impeller downwards, on a flat
surface. Unscrew grille securing screw located at the
top of the grille.
E2Remove grille.
Partially unscrew the two safety
catch screws on the face of the housing
E3Depress the side catches.
E4Lift off the housing.
E5Ease back the motor support safety catch, located to
the left of the connector socket opening. Rotate motor
support assembly anti-clockwise, until the bayonet
catches disengage.
E6Withdraw motor support assembly and place with
the impeller downwards.
CONJUNCTION
FITTING AND WIRING
Measure glass thickness and determine length of fixing
screw required. For glass 2-18mm, break off ends of
screws supplied; 16-32mm, use screw as supplied.
F1From inside: Place the spigot centrally through the
fixing hole and with the connector hole upwards.
CURRENT
IEE
Ensure rubber seal is correctly located over lugs and
around the spigot.
F2iFrom outside: Place the exterior grille assembly
over the projecting spigot.
louvers are slanting downwards.
F2iiFrom outside: Place the exterior cowl over the
projecting spigot.
should be bedded in a suitable sealing compound.
F3i/F3iiInsert screws through the holes around the
spigot.
progressively and in turn to give an even pressure round
the hole.
F4a/F4b Locate and replace the motor support
assembly and turn clockwise until the safety catch is
fully engaged.
F5If the unit is to be wired through a T-Series Single
Unit Controller, the speed control pack must be
removed from the unit and plugged into the T-Series
Controller.
Instructions). If the unit is to be wired through an
on/off switch, it can be preset at one of three speeds. It
is factory set for high speed (Position III).
medium speed is required, remove speed control pack
and insert it in Position II. If low speed is required
BATH
OR
insert in Position I.
F6Replace housing with connector slot uppermost.
F7With the two side catches fully engaged, tighten the
catch safety screws.
F8Replace interior grille with louvers slanting upwards.
Engage the bottom edge first then push the top home.
Tighten the securing screw at the top of the grille.
OR
INFIRM
WARNING
EARTHED.
SHOULD
BE
WIRING THE CONNECTOR SOCKET
F9Remove the top cover from the connector socket by
undoing the 2 retaining screws.
F10Lift up lever and slide out top cover.
F11Loosen cable clamp screws and pass the cable
through the clamp. (It may be necessary when using
some 3-core cables to reverse the cable clamp to ensure
that the cable is securely retained. For ease of wiring,
the terminal block may be removed from the connector
housing.
Note:
If the unit is to be wired through a T-Series single unit
controller, strip wires of the 5-core cable, see controller
wiring instructions for connections and continue from
F14. Check if wiring through an on/off switch for
single speed extract or intake use, strip wires then
connect to a suitable 3 pin plug or, if permanently
wired, a double pole isolator switch having a contact
separation of not less than 3mm must be provided.
For extract operation
F12Connect Live (brown) to terminal L3, Neutral
(blue) to terminal N and Earth (green/yellow) to
terminal E/G in the connector socket. Link terminal L3
to L1.
For intake operation
F13Connect Live (brown) to terminal L3, Neutral
(blue) to terminal N and Earth (green/yellow) to
terminal E/G in the connector socket. Link terminal L3
to L2.
F14 Tighten cable clamp screws evenly, ensuring a
secure grip on the outer sheath of the cable.
F15Slide the top cover back on and secure with the 2
retaining screws.
F16Fit connector socket and push down on the lever to
lock it in position.
WINDOW MODEL 240V / 1 / 50Hz Watts on high
SIZE
6
7
9
12
Performance guide in m
Ensure that the grille
When fitting, the cowl assembly
With the fingers, tighten the screws
(See Controller Fitting and Wiring
THIS
APPLIANCE
MUST
HIGH
MEDIUM
LOW
WATTS
360
315
245
485
395
305
795
685
465
1615
1415
1095
3
/h and max. watts input
ROOF MODEL 240V / 1 / 50Hz Watts on high
SIZE
HIGH
6
290
7
485
9
795
12
1485
FOR THE USER
CLEANING
Apart from removing odours, your Vent-Axia fan also
extracts airborne impurities such as dirt, dust and
grease. These gradually build up and detract from the
efficiency and appearance of your fan. The Vent-Axia
T-Series fans are designed for easy cleaning and
maintenance. Therefore, to ensure peak performance of
your fan it should be regularly cleaned.
IMPORTANT; SWITCH OFF AND ISOLATE UNIT
FROM MAINS SUPPLY.
Dismantling
Disconnect mains supply.
G1Remove connector socket by lifting up the lever
gently with a finger.
G2Unscrew the grille securing screw and remove grille.
G3Partially unscrew the two safety catch screws on the
face of the housing until the side catches can be
If the
depressed.
G4Withdraw the housing assembly.
G5Ease back motor support safety catch to the left of
the connector socket opening.
G6Rotate motor support assembly anti-clockwise and
withdraw it.
G7Remove impeller with a sharp pull.
G8Window model only – to remove grille from outside,
unscrew grille securing screw.
Cleaning
G9Wipe motor and housing assembly with a damp
BE
cloth.
IMPORTANT keep electrical components away from
water.
G10Wash all non-electrical parts in warm water and
detergent. Wipe inside of roof cowl assembly with a
damp cloth.
Re-assembly
G11Align marks on impeller with locating pins on
motor shaft. With a sharp push, replace impeller back
onto motor shaft. Ensure that the impeller snaps into
position.
G12Window model only - replace outside grille (with
louvers pointing downwards). Engage top edge first
then push the bottom home. Tighten grille securing
screw.
G13From the inside replace motor support assembly
and turn it clockwise until the safety catch is fully
engaged.
G14Replace housing.
G15Ensure that the two side catches are fully engaged.
Tighten the catch safety screws.
G16Replace the interior grille (with the louvers
pointing upwards). Engage bottom edge first then push
the top home. Tighten grille securing screw.
G17Replace connector socket and push down on the
lever to lock it in position. Restore the mains supply
and check fan function.
The motor in this Vent-Axia product is fitted with
sealed-for-life bearings and therefore does not require
lubrication.
WARNING
DO NOT INSTALL A YELLOW SPEED CONTROL
PACK INTO A GREY SOCKET OR VICE VERSA.
WARNING
IF USING A T-SERIES CONTROLLER, THE
YELLOW SPEED CONTROL PACK MUST BE
REMOVED FROM THE UNIT AND INSTALLED
INTO THE CONTROLLER.
30
Available Controllers
40
For single fans up to 120 Watts:
W36 11 19(TSC Controller)
85
W30 01 20(Ecotronic 130)
105
For multiple fan applications up to 400 watts:
W36 23 20(Ecotronic 400)
MEDIUM
LOW
WATTS
250
195
30
395
305
40
685
465
85
1305
1010
105
