Agri-Fab 45-05431 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Agri-Fab Manuales
  4. Esparcidores
  5. 45-05431
  6. Manual de instrucciones
Agri-Fab 45-05431 Manual De Instrucciones

Agri-Fab 45-05431 Manual De Instrucciones

Ocultar thumbs

Enlaces rápidos

32" POLY SPIKER/SPREADER
..................................................................4
ENGLISH..........................................................6
Without your product review, we don't exist.
Customer Care
M-F 7:00 a.m. - 5:00 p.m. CST
800-448-9282
www.agri-fab.com
the fastest way to purchase parts www.speedepart.com
45-05431
THANK YOU
FOR YOUR PURCHASE!
If you are happy with our quality products & service,
please take just a moment to leave positive feedback and
a short review of our product on our website or your retailer's website.
Not totally satis ed?
If you have any issues, don't hesitate to contact us.
We make mistakes sometimes, but please give us the chance
to make it right before leaving negative feedback against our product.
ESPAÑOL..........................................................13
fRANÇAIS.........................................................16
MADE IN
USA
WITH GLOBAL COMPONENTS
FORM NO. 45941 (03/24/2020)
loading

Manuales relacionados para Agri-Fab 45-05431

Resumen de contenidos para Agri-Fab 45-05431

  • Página 1 45-05431 32" POLY SPIKER/SPREADER ..............4 ESPAÑOL............13 ENGLISH............6 fRANÇAIS............16 THANK YOU FOR YOUR PURCHASE! Without your product review, we don’t exist. If you are happy with our quality products & service, please take just a moment to leave positive feedback and a short review of our product on our website or your retailer’s website.
  • Página 2 PARTS fOR 32" POLY SPIKER/SPREADER MODEL 45-05431...
  • Página 3 PARTS fOR 32" POLY SPIKER/SPREADER MODEL 45-05431 REf. PART NO. QTY. DESCRIPTION REf. PART NO. QTY. DESCRIPTION 47953 COVER, CHAIN R19171616 WASHER, .531 X 1 X .059 24743BL1 LEVER, FLOW CONTROL 43081 WASHER, .375 X .875 X .083 24747BL1 BRACE, CENTER...
  • Página 4 RULES fOR SAfE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Wear eye and hand protection when handling and using • Read this owner's manual before attempting to assemble lawn chemicals. or operate the spiker/spreader. • Always begin with the transmission in first (low) gear and • Read the towing vehicle owner's manual and know how gradually increase speed as conditions permit. Maximum to operate the tractor before using the spiker/spreader towing speed - 3 M.P.H. attachment. • Do not drive too close to a creek or ditch and be alert • Do not allow anyone to ride on or sit on the spiker/ for holes and other hazards which could cause you to spreader. lose control of the tractor and spiker/spreader. • Never allow children to operate the tractor or spiker/ • Before operating the vehicle on any grade (hill) refer to spreader attachment.
  • Página 5 43661 44215 44180 44292 (12) 46524 741-0249 47025 47189 (13) 45100 47810 44731 43009 43182 44101 43093 47623 43019 43088 1543-69 43081 R19212016 R19171616 NOT SHOWN FULL SIZE 43848 43943 47959 712-0421 24571 47960 47777 49449 46497 23520 47969...
  • Página 6 ASSEMBLY TOOLS REQUIRED fOR ASSEMBLY • On the right side, assemble the handle brace bracket (2) 7/16" Wrenches (5) to the lift handle (9) using a 5/16" x 3/4" hex bolt (32) (2) 1/2" Wrenches and 5/16" nylock nut (27). Tighten. See figure 2. (2) 3/4" or Adjustable Wrenches • Assemble the grip (45) onto the lift handle. (1) Screwdriver (1) Pliers Spike points are sharp. Exercise caution when handling and working near spike disks. fIGURE 2 • Attach a hitch tube to the right hand side of the hopper using two 5/16" x 2" hex bolts (17), 5/16" flat washers (35) and 5/16" nylock hex nuts (27). Assemble the bolts and washers from inside the hopper. Insert a tube plug (48). Tighten. Repeat for the other side. • Insert a 5/16" x 3-1/2" hex bolt (14) through the transport tube (10), the lift handle (9), a spacer (42), and through the hitch tube. Secure with a 5/16 nylock nut (27). • Insert a 5/16" x 2" hex bolt (17) through the transport tube (10), two 5/16" flat washers (35), and the handle brace bracket (5). Secure with a 5/16" nylock nut (27). Tighten. See figure 3. fIGURE 1 fIGURE 3...
  • Página 7 • On the left side, insert a 5/16" x 3-1/2" hex bolt (14) • Attach the hitch brackets (13) to the hitch tubes using through the upper hole on the transport tube (10), a two 5/16" x 2" hex bolts (17) and 5/16" nylock hex nuts spacer (42), and the hitch tube. Secure with a 5/16 (27). Do not tighten yet. See figure 6. nylock nut (27). Do not tighten yet. See figure 4. • Install the hitch pin (21) through the hitch brackets (13), and secure with a 3/32 hair cotter pin (25). Tighten all loose bolts and nuts that have been • assembled. fIGURE 4 fIGURE 6 • Fasten the hitch tubes together using three 5/16" x 2-1/2" hex bolts (15) and 5/16" nylock hex nuts (27). Do • Assemble a 1/2" x 4" hex bolt (16), a .531 washer (34), not tighten yet. See figure 5. a wheel (6), a .531 washer (34), and a .5" jam nut (29). finger tighten only. • Attach the wheel assembly to the transport tube using a 1/2" nylock jam nut (28). Repeat for the other side. See figure 7.
  • Página 8 • Screw a 1/4" nylock hex nut (26) all the way onto the • Place the flow control lever into the slot in the hopper. flow control link (44). Assemble the ferrule (46) onto the See figure 9. link and then start a 1/4" nylock hex nut one or two turns • Place the center brace (3) into the hopper. Insert a onto the link. See figure 8. 1/4" x 1" hex bolt (19) through the center brace and the • Assemble the ferrule (46) into the hole at the end of front of the hopper. Assemble a nylon washer (36), the the flow control lever (2) using a 1/4" nylock hex nut (26). flow control lever and a 1/4" nylock hex nut (26) onto the Tighten the nut, leaving it loose enough that the ferrule bolt. Do not tighten yet. See figure 9. can pivot. See figure 8. • Insert the other 1/4" x 1" hex bolt (19) through the • Assemble the grip (43) onto the end of the flow control center brace and the rear of the hopper. Assemble a 1/4" lever. See figure 8. flat washer (37) and 1/4" nylock hex nut (26) onto the bolt. Tighten both the front and rear bolts. See figure 9. fIGURE 9 • Insert the 5/16" x 1-3/4" carriage bolt (18) up through the slot and secure it with a nylon washer (36) and the fIGURE 8 plastic wing nut (39). See figure 10. • Move the lift handle into the locked position as shown in figure 10 and then tip the spreader back to rest on the wheels and the rear of the hopper.
  • Página 9 • Move the flow control lever (2) as far as it will go to • Push a flanged bearing (22) into each side of the drive the "OFF" position. Push the feed plate back as far as it disk (8). See figure 12. will go to the closed position. See figure 11. • Place the bent end of the flow control link (44) into the feed plate bracket and a 1/4" flat washer (37). Secure it with a 3/32" x 3/4" cotter pin (24). See figure 11. • Tighten the lower 1/4" nylock hex nut (26) until it touches the bottom of the ferrule, then tighten the upper 1/4" nylock hex nut (26) until it is snug against the top of the ferrule. See figure 11. • Open and close the feed plate using the flow control lever. Check to make sure the feed plate is closed completely when the lever is in the "OFF" position. If the feed plate does not close completely, adjust the 1/4" nylock hex nuts (26) on the flow fIGURE 12 control link (44). See figure 11. • Push a flanged bearing (22) into each of the eight spike disks (7), from the side shown in figure 13. NOTE: Forcing the flow control lever may result in PERMANENT DAMAGE to the feed plate! fIGURE 13 • Press flanged bearings (22) into both of the end plates. See figure 14. •  Place the 1/4" thick spacer (40) onto the spike disk shaft (12) and then insert the shaft through the flanged bearing (22) in the left hand end plate. See figure 14.
  • Página 10 • Place a large washer (38), short spacer tube (41), and • Place a 5/8" flat washer (33), the compression spring the drive disk (8) onto the shaft. Fit the short spacer tube (49) and another 5/8" flat washer onto the shaft. See and large washer onto the flanged bearing in the end figure 17. plate. See figure 15. 41 38 fIGURE 17 fIGURE 15 • Place two spike disks (7), separated by a long spacer tube (20), onto the shaft. Fit the long spacer tube onto the ends of the flanged bearings in the disks. See figure 18. • Place two spike disks (7), separated by a long spacer tube (20), onto the shaft. Fit the long spacer tube onto the ends of the flanged bearings in the disks. See figure 16. fIGURE 18 • Place a long spacer tube (20) onto the shaft. See figure 19. fIGURE 16 fIGURE 19...
  • Página 11 • Place two spike disks (7), separated by a long spacer • Place a 5/8" flat washer (33) onto the end of the spike tube (20), onto the shaft. Fit the long spacer tube onto the disk shaft and secure the shaft with a 1/8" x 1-1/2" cot- ends of the flanged bearings in the disks. See figure 20. ter pin (23) by spreading the ends of the cotter pin. See figure 23. • Fasten the drive disk to the shaft using a 1/8" x 1-1/2" cotter pin (23) by spreading the ends of the cotter pin. See figure 23. fIGURE 20 • Place a long spacer tube (20) onto the shaft. • Place two spike disks (7), separated by a long spacer tube (20), onto the shaft. Fit the long spacer tube onto the ends of the flanged bearings in the disks. See figure 21. fIGURE 23 • Remove connecting link from chain and assemble the chain (47) onto the two sprockets on the left side of the hopper. Fasten the ends of the chain together using the connecting link. See figure 24. • Place the chain cover over the chain and fasten it to the hopper end plate using two self tapping screws (31). See figure 24. fIGURE 21 • Place a short spacer tube (41) and then a large washer (38) onto the shaft. Fit the short spacer tube and washer onto the end of the flanged bearing in the end plate. Push the shaft on through the flanged bearing in the end plate. See figure 22. CONNECTING LINK fIGURE 24...
  • Página 12 OPERATION SETTING CHART flow Rate Setting MATERIAL TYPE At 3 M.P.H. HOW TO USE YOUR SPIKER/SPREADER Fertilizer Granular / Pelleted 0-1 / 0-2 1. Refer to the instruction label on the material package and to the instruction decal on your spreader to help Grass Seed Fine / Coarse 5-6 / 7-8 determine the proper spreader setting and application 3 M.P.H. is equivalent to traveling 100 feet in 23 seconds. rate. A lso see the Setting Chart on this page for a general range of settings for commonly used materials.

  • Página 13: Reglas Para Una Operación Segura

    ESPAÑOL REGLAS PARA UNA OPERACIÓN SEGURA Cualquier equipo motriz puede causar lesiones si no se opera correctamente o si el usuario no entiende la forma de operar el equipo. Tenga siempre cuidado cuando use un equipo motriz. • Lea este manual de instrucciones con mucho cuidado antes • Use protección para sus ojos y sus manos cuando maneje y de tratar de armar u operar este surcador-esparcidor. aplique productos químicos para el césped. • Lea el manual de instrucciones del tractor y conozca bien la • Siempre comience con la transmisión en primera (baja) forma de operar el tractor antes de usar este equipo surcador- velocidad y aumente la velocidad gradualmente como lo esparcidor. permitan las condiciones. La velocidad máxima de remolque • No permita que nadie se monte ni se siente sobre el surcador- es 10 M.P.H. (16 kilómetros por hora). esparcidor. •...
  • Página 14 • Monte el casquillo (46) en el orificio del extremo de la palanca • Coloque los cojinetes embridados (22) en ambas placas de control de flujo (2) con una tuerca hexagonal de seguridad terminales. Consulte la figura 14. de nylon de 1/4" (26). Apriete la tuerca, pero déjela lo bastante suelta como para que el casquillo pueda girar. Consulte la • Coloque el separador grueso de 1/4" (40) en el eje del disco figura 8. surcador (12) y luego inserte el eje por el cojinete embridado (22) en la placa terminal derecha. Consulte la figura 14. • Monte el mango (43) en el extremo de la palanca de control de flujo. Consulte la figura 8. • Coloque una arandela grande (38), un tubo separador corto (41), y un disco de accionamiento (8), en el eje. Coloque arandela • Coloque la palanca de control de flujo en la ranura de la tolva. grande y el tubo separador corto en el cojinete embridado de Consulte la figura 9. la placa terminal. Consulte la figura 15. •...

  • Página 15: Operación

    ESPAÑOL OPERACIÓN CUADRO DE AJUSTE fORMA USAR EQUIPO SURCADOR- MATERIAL TIPO Ajuste de la cantidad de flujo a 3 M.P.H. (4.8 kph) ESPARCIDOR Fertilizante Granular / En forma 0 - 1 / 0 - 2 de pelotillas 1. Lea la etiqueta de instrucciones en el paquete de materiales y la calcomanía de instrucciones en el esparcidor para Semilla Fina / Gruesa 5 - 6 7 - 8 determinar el ajuste apropiado del esparcidor y la velocidad...
  • Página 16 fRANÇAIS RÈGLES DE SÉCURITÉ D’UTILISATION Tout équipement à moteur peut causer des blessures s’il est mal utilisé ou si l’utilisateur ne sait pas comment l’utiliser. Il faut faire attention en permanence pour utiliser l’équipement à moteur. et utiliser les produits chimiques de pelouse. • Lire ce manuel du propriétaire avant d’essayer d’assembler • Commencer toujours avec la boîte de vitesse en première ou d’utiliser la cramponneuse/répandeuse. (vitesse basse) et augmenter graduellement la vitesse selon • Lire le manuel du propriétaire du véhicule remorqueur et bien les conditions. Vitesse maximale de remorquage : 16 km/h (10 savoir comment utiliser le tracteur avant d’utiliser l’accessoire milles/hr). de cramponneuse/répandeuse. • Ne pas conduire trop près d’un ruisseau ou un fossé et faire • Ne permettre à personne de monter ou de s’asseoir sur la attention aux trous et autres dangers qui pourraient causer cramponneuse/répandeuse.
  • Página 17 • Visser un écrou nylock de 1/4 po (26) jusqu’à la tige de • Insérer un palier avec bride (22) dans chacune des plaques commande de débit (44). Assembler la ferrule (46) sur la tige d’extrémité. Voir figure 14. et puis visser un écrou nylock hexagonal de 1/4 po un ou deux tours sur la tige. Voir figure 8. • Placer le manchon d’espacement de 1/4 po (40) sur l’arbre de disques éperons (12) et puis insérer l’arbre à travers le •...
  • Página 18 fRANÇAIS fONCTIONNEMENT TABLEAU DE RÉGLAGE MATÉRIAU TYPE Réglage de débit à COMMENT UTILISER CRAMPONNEUSE/ 5 km/h (3 milles/hr) RÉPANDEUSE Fertilisant Granulaire / à boulettes 0-1 / 0-2 1. Se reporter à l’étiquette d’instructions sur l’emballage du matériau et à l’autocollant d’instructions sur la répandeuse Semence Fine / lourde 5-6 / 7-8 pour aider à déterminer le réglage et le taux d’application...
  • Página 20 REPAIR PARTS Agri-fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com...