Características - MORDOMUS iSF22 Guia De Inicio Rapido

Take care not to power up more than one iSFXX or iSHXX device at the
same time since WPS allows for configuration of only one device at a
time. We recommend powering up and registering the devices in a sequential
manner.
2. Press the WPS button on the router according to the user manual of this
device and wait until the WPS negotiation is completed. This is signaled by 2
short blinks of the connection status indicator every 2 seconds.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations → Modules/
Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iSF22 device for
safety reasons.
4. After the iSF22 device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain off.
From now on the iSF22 device is ready to use.
Method 2 - Manual Setup
1. Activate AP mode and access the configuration page as described in section
5.
2. Enter the (SSID) in the field WiFi Name and password WiFi password. Enter
the Mordomus Home Name in the field Home Name as defined in Mordomus -
> Configurations -> Connectivity: Mordomus Home Name.
By entering the house name, the fields Mordomus local IP and Mordomus
Port should be left blank.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations → Modules/
Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iSF22 device for
safety reasons.
4. After the iSF22 device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain off.
From now on the iSF22 device is ready to use.
3. Connection Status indicator codes
WPS discovery mode.
Connected to Wifi and searching Mordomus.
iSF22
Access Point mode for manual configuration.
Connecting to Router.
4. Resetting the device to factory defaults
1. Enter AP mode and access the configuration page as described in section 5.
2. Click on the Button Reset all.
5. Activating AP Mode (Access Point)
1. Touch and Hold the touch button 1
activate Access Point mode. This is signaled by 3 short blinks of the connection
status indicator every 2 seconds. (Possible beep sounds should be ignored).
2. Using a wireless device (Laptop, tablet, smartphone) connect to WI-FI
network SSID iSF22_1234 using the password 00000000 (eight zeroes).
The last four digits of the SSID are the same as the last four digits of the
device's serial number. This mode is limited to 5 minutes on the iSF22
device for safety reasons.
3. In the address bar of the browser of the device enter the IP 192.168.4.1 in
order to access the configuration page of the iSF22.
5.1. Configuration page
The configuration page of the iSF22 allows for a manual configuration of:
WiFi Name
WiFi Password
Mordomus Home Name
Mordomus Local IP
Mordomus port
The Reset all button resets all of the above settings and other configurations to
the factory default values.
This product complies with the Electromagnetic
Compatibility Directive 2014/30/EU.
This product conforms with the EU Directive 2011/65,
RoHS
regarding the restriction of use of certain hazardous
substances in electric and electronic devices.
For EU countries only.
All old electrical and electronic devices must be
separated from normal household waste and disposed
of at designated facilities. For further information
contact your local authorities, waste disposal office or
the shop where you bought the device.
PT
iSF22 – Interruptor mural tátil 2 canais
Wi-Fi
Características:
• 2 saídas relé com indicador luminoso de estado.
• 2 entradas táteis.
Aplicações:
• Interruptor tátil mural para controlo de iluminação ou aparelhos
v.1927
of the iSF22 for at least 12 seconds to
http://mordomus.com/
mordomus/docs/wifi/i
SF22.pdf
2/6