Tabla de contenido
Enlaces rápidos
Tabla de contenido
Manuales relacionados para Ubiquiti Networks NanoSwitch N-SW
Resumen de contenidos para Ubiquiti Networks NanoSwitch N-SW
- Página 1 Outdoor 4-Port PoE Passthrough Switch Model: N-SW...
-
Página 2: Package Contents
Introduction Thank you for purchasing the Ubiquiti Networks® NanoSwitch . This Quick Start Guide is designed to guide you ™ through installation and also includes warranty terms. Package Contents Outdoor 4-Port PoE Passthrough Switch Model: N-SW NanoSwitch Metal Straps Quick Start Self-Tapping (Qty. - Página 3 • Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the N-SW and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.
-
Página 4: Hardware Overview
Hardware Overview System LED Port Cover The LED will light blue when the device is powered on. - Página 5 Link PoE In PoE Out Ground Bonding Point with a Machine Screw and Nut RJ45 LEDs State Status Green Active 24V PoE Link Green Link Established Flashing Indicates Activity Ports Port Description PoE In RJ45 port supports 10/100/1000 Ethernet connections and supports 24V, 2-pair passive PoE to power the switch.
- Página 6 Ground Bonding Point The NanoSwitch must be grounded in one of the following ways: • Use the Self-Tapping Screw to ground the NanoSwitch directly to a grounded metal pole or structure. • Use the Machine Screw and Nut to attach a drain wire (not included) that is connected to a remote grounding block or structure.
-
Página 7: Hardware Installation
Hardware Installation Install the NanoSwitch either on a pole or a wall. Follow the appropriate steps for your installation: Pole-Mounting 1. Feed the included Metal Straps through the slots located on the back of the NanoSwitch. 2. Wrap the Metal Straps around the pole. Use a 7 mm socket wrench or screwdriver to turn the screws clockwise and securely fasten the straps to the pole. - Página 8 3. Remove the Port Cover by pressing on its center and sliding it down. Note: If you are using a drain wire for grounding, proceed to the Connecting Power section. 4. Remove the Self-Tapping Screw and nut from the Ground Bonding Point, and drill a 4.5 mm pilot hole into the pole.
- Página 9 5. Insert the Self-Tapping Screw into the pilot hole. Securely fasten the screw to ensure the Ground Bonding Point is bonded to the pole. Wall-Mounting 1. Secure two screws (not included) to the wall, spaced 38 mm apart. 38 mm 2. Leave a gap of 3 mm from each screw head to the wall. 3 mm ≤...
- Página 10 3. With the drain wire already attached, insert the screw heads into the Keyhole Slots on the back of the NanoSwitch. Press down on the NanoSwitch to secure it. Keyhole P o E L I N Slots *640-00314-07* 640-00314-07...
-
Página 11: Connecting Power
Connecting Power The NanoSwitch is powered by PoE. Connect an Ethernet cable from a passive 24V, 2-pair PoE power source to the PoE In port. Connecting Ethernet WARNING: PoE is always active. Before connecting a device to a PoE Out port, ensure that the device supports passive PoE and the supplied voltage. - Página 12 Specifications N-SW Dimensions 196.4 x 93.5 x 32.4 mm (Excluding Mount) ( 7.73 x 3.68 x 1.28") Weight 271 g (9.6 oz) Enclosure Characteristics White Polycarbonate Total Non-Blocking Line Rate 4 Gbps Typical Power Consumption 1.5W Max. Power Consumption Power Method 24V, 2-Pair Passive PoE Networking Interfaces (4) 10/100/1000 Mbps Ethernet RJ45...
-
Página 13: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. - Página 14 Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
- Página 15 Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
- Página 16 RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Página 17 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Página 18: Declaration Of Conformity
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/compliance Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta N-SW tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance... -
Página 19: Online Resources
2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka N-SW ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/compliance Lietuvių... - Página 20 Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 ©2017-2019 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, NanoSwitch, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc.