golmar Tekna-S Gtwin Guía Rápida página 4

DESCRIPTION
D
escription of the TEKNA-S GTWIN monitor.
Monitor for installation of the Gtwin system with button and coded
panels.
a k
b
l
m
c
n
g
o
h
p
d
q
i
k
j
- State of the door on the main
panel:
e
LED illuminated red. (see the
TGtwin System Manual, p. 10).
- State of the door on the slave
door panel:
LED blinking red. (See the
f
TGtwin System Manual, p. 10).
- Programming mode:
LED blinking yellow.
a. Handset.
Monitor indicator LED:
j.
b. 4.3" TFT colour screen.
- Standby: Off.
c.
Communication with hearing aids. Set
- Call/communication/auto spy:
the hearing aid switch to position T.
LED illuminated green.
d.
Function/programming buttons.
Connector fixings.
k.
e. Telephone cord.
l. J2 jumper (end of line) or EL-566
f.
Cord connector.
in-out unit connector (see the
g. Brightness control.
TTekna S Gtwin manual).
h. Colour control. m. SW2 configuration switch.
i. Monitor status LED:
n. SW1 configuration switch.
- No volume: LED blinking red rapidly.
o. CN5 connector (no function).
- Doctor mode: LED blinking green.
p. CN1 connection terminals.
q. CN2 connection terminals.
D
escription of the connection terminals.
CN1 connection terminals:
LINE LINE
IN OUT
Communication bus input to monitor (non-polarised).
LINE IN:
LINE OUT: Communication bus output to additional monitor/telephone
(non-polarised).
CN2 connection terminals:
_
CP S+ S
CP : Input for calls from the apartment front
S+ : Output (positive) to auxiliary call repeater SAV-GTWIN.
S : Output (negative) to auxiliary call repeater SAV-GTWIN.
DESCRIPTION
1
F
unction buttons.
In standby and with the handset off the hook: it activates the intercom
between 2 devices in the same apartment or in different apartments
(this feature must be pre-programmed, see the TTEKNA S GTWIN, pp.
12-15).
During a call, communication or auto-spy process: it enables the
TEKNA-S GTWIN
12050225 V
XX
.
15090200000
SN ADDRESS secondary lock release to be activated: one press will activate the lock
INTER A1 SLAVE MASTER
ESCALERA PISO PUERTA
STAIR FLOOR DOOR
ATENCIóN release for 1 second.
Alta tensión. No abrir la tapa.
Manipular sólo por personal
del servicio técnico.
WARNING. GOLMAR S.A
High Voltage. Don´t open cover C/ Silici, 13
Handle only by technical service 08940 - SPAIN
In standby and with the handset off the hook: it enables a call to be made
to the guard unit.
In standby and with the handset off the hook: it activates the intercom
SW1 SW2
1 2 3 4 5 6 7 8 9 10 1 2
between 2 devices in the same apartment or in different apartments
CN5
J2
CN1
(this feature must be pre-programmed, see the TTEKNA S GTWIN,
pp. 12-15).
CN2
Note: Activation of the
unit' function.
In standby and with the handset on the hook: it enables programming
mode to be entered or exited by pressing and holding for 5 seconds, a
number of short audible tones will indicate that the monitor is in
programming mode and the status LED will blink slowly (yellow) or a
number of long audible tones will indicate that the monitor has saved
and left programming mode, and the status LED will turn off.
In standby and with the handset on the hook: it enables the image from
the door panel configured as main to be viewed (if the channel is busy,
a number of short audible tones on the monitor will indicate so); if the
handset is then picked up, it enables audio and video communication
with the door panel to be established.
During a call process: it enables the slave monitors (in the same
apartment) to capture the image of the door panel, with the image on
the monitor that was displaying it disappearing.
In standby and with the handset off the hook: it activates the intercom
between 2 devices in the same apartment or in different apartments
(this feature must be pre-programmed, see the TTEKNA S GTWIN,
pp. 12-15).
No function.
During call reception and communication processes, it enables the main
lock release to be activated.
OPERATION
- Call reception: During call reception, the image will appear on the master
monitor, and the indicator LED on the master and slave monitors will
illuminate (green). If the call is not answered within 60 seconds, the status
LED on the master and slave monitor(s) will turn off. LED
panel will turn off and the channel will become free.
- To establish communication, pick up the monitor handset, the status LED will
remain illuminated (green), LED
LED on the door panel will turn off. Communication with hearing aids
: the handset enables communication with hearing aids equipped with T-
mode, making conversation possible (inductive loop).
- Guaranteed communication time is 90 seconds (configurable); after 90
seconds of guaranteed communication time, the channel will become free.
- To end communication, hang up the handset, the indicator LED on the
monitor and LED
become free.
- To open the main or secondary door, press the corresponding door release
door.
button /
activate the lock release for 1 second (configurable main door) and, with the
opening of the main door, LED
second.
'intercom' function disables the 'call to guard
on the door
on the door panel will now illuminate and
on the door panel will now turn off and the channel will
during the call or communication processes: one press will
on the door panel will also illuminate for 1
INSTALLATION
2
I
nstallation of the monitor
Avoid dusty or smoky environments or locations near sources of heat. The
monitor can be fixed to an electrical embedding box or directly to the wall.
Important: For further information, see the TTekna S Gtwin
Location
manual (code 50120265).
Remember to remove the protective covering
1.60m
from the front of the monitor once installation
is complete.
Surface
4 30 x
ADVANCED PROGRAMMING
Advanced programming of the functions of the Tekna-S Gtwin monitor:
Advanced programming enables the monitor's default settings to be changed:
With the monitor in standby: Press button
seconds to access
tones will confirm this and the monitor's status LED will blink
(yellow) slowly, indicating that button
Then adjust the settings as required:
- Adjusting the call volume: Maximum volume (default setting).
The monitor enables call volume control (maximum/minimum/no volume).
Press button until you hear the desired volume. Options: maximum,
minimum and no volume (if set to 'no volume,' the monitor's status
LED will blink red rapidly when the monitor exits programming mode
and is in standby) 'carousel' mode.
- Changing the door panel ringtone melody:
The monitor enables selection of the ringtone (5 different tones).
Select the ringtone melody: Press button
heard 'carousel mode.'
- Changing the ringtone melody from the apartment front door:
The monitor enables selection of the ringtone from the apartment front door
(5 different tones).
Select the ringtone melody from the apartment front door: Press button
until the desired melody is heard 'carousel mode.'
- Activating/deactivating the doctor mode function: Doctor mode not activated
(default setting).
The 'doctor mode' function enables the main lock release to be activated
automatically 3 seconds after making a call from the door panel without having to
establish communication or press door release button
15 seconds and the channel becomes free. (Only the master monitor should be
configured with 'doctor mode').
To activate doctor mode: Press button
that the function is activated; if it is pressed again, an audible tone will
indicate that the function will change its status to deactivated and so on. The
monitor's status LED will blink (green) when the monitor exits programming
mode and is in standby.
3
Embedding box
Screws supplied with
the embedding box.
for more than 5
'programming mode,' 3 short audible
can be released.
until the desired melody is
. The call ends after
once, an audible tone will indicate
Continued overleaf