Cold Weather Operation - Delta DCN701 Traducido De Las Instrucciones Originales


WARNING: Always remove battery pack before loading or
unloading staples.

CAUTION: Keep fingers clear of pusher latch track to
prevent injury.

WARNING: This stapler requires the use of
D WALT staples.
e
1. Depress magazine release button
core and pusher out until it reaches the end of its travel.
8
2. Drop staple strips into the loading slot of the magazine
making sure the staple heads align correctly with the
slot opening. (Refer to Technical Data to determine
compatible size.)
3. Keeping fingers clear of the track, close the magazine by
releasing the pusher latch. Carefully allow the latch to slide
forward and engage the staple strip.
nOTE: Do not slam magazine core assembly into magazine
or you could damage staples.
Unloading the Tool

WARNING: Always remove battery pack before loading or
unloading staples.
1. Depress magazine release button
core and pusher 8 out until it reaches the end of its travel.
2. Tip the tool right side up until the staple strips fall freely out
of the magazine.
3. Close the magazine by sliding the magazine core back into
the magazine fully until it latches. Do not slam magazine
core into the magazine.
Headlight/LED Worklight (Fig. F)
There is a headlight/LED worklight
unit. The headlight turns on upon battery insertion, activation
of the trigger, or depressing the contact trip. The light will
automatically shut off after 20 seconds unless tool remains
in use.
nOTE: The headlight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
LOW BaTTERY InDIcaTOR: The headlight will flash four
consecutive times and then shut down to indicate low battery.
Actuating the Tool (Fig. G)

WARNING: Always turn off power to circuit before
attempting to staple wires. Do not staple "live" wires.

WARNING: Always assume that the tool contains staples.
Careless handling of the stapler can result in unexpected
firing of staples and personal injury. Do not point the tool
towards yourself or anyone nearby. Unexpected triggering
could discharge a staple causing an injury. No horseplay!
Work Safe! Respect the tool as a working implement.

WARNING: Do not actuate the tool unless the tool is
placed firmly against the workpiece. If the tool is not in
contact with the workpiece, the staple may be deflected
away from your target.
There is no need for depth adjustment.
1. Load unit with staples.
2. Place battery into tool.
7 and slide the magazine
6 ,
and slide the magazine
7
5 located at the front of the
3. Locate cable alignment guide
wire you wish to staple so that the wire is centered as much
as possible between the 2 prongs of the cable guide.

WARNING: Staples must be driven straight into the material. Do not tilt stapler while driving staples. Refer to
Figure G. Staple retention values improve when tool is fired
perpendicular to the material.
4. Push tool against cable firmly to depress cable alignment
guide all the way as well as wire indicator
3
trigger 1 and a staple will be fired.
5. Check wire for damage after each shot.
nOTE: When fastening into certain wood materials, additional
force applied towards the wood may be needed to properly
seat the staple.

WARNING: Use caution in locating stapler over cable or
wire to prevent the staple from piercing the cable jacket or
insulation. After firing each staple, visually inspect driven
staple to make sure wire insulation was not damaged. If
damaged replace wire.
Clearing a Jammed Staple (Fig. A, H)

WARNING: To reduce the risk of serious personal injury,
disconnect battery pack from tool before making any
adjustments, changing accessories, servicing, or moving
the tool. Such preventative safety measures reduce the risk
of firing the tool accidentally.
1. Remove battery pack 10 from tool.
2. Depress magazine latch 7
pusher 8 out until it reaches the end of its travel.
3. Tip the tool right side up until any loose staple strips fall
freely out of the magazine. Any jammed staples can then
be removed.
4. Refill magazine with new staples.

Cold Weather Operation

When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool a few times into scrap lumber over a piece
of scrap cable before using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before loading staples, making any adjustments or
removing/installing attachments or accessories. An
accidental actuation can cause injury.
The charger and battery pack are not serviceable.
EnGLIsh
directly over the cable or
3
, pull
4
and slide the magazine core and
39