Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PARTS OF THE HEATER
Parts of the Heater
Symbols
1. Control Panel
Power Button
2. LED Display
H/L Heat Button
3. Safety Grille
Oscillation Button
4. Base
Plus Button
5. Remote Control
Minus Button
6. Power Light
Timer Button
Temperature Setting Button
ASSEMBLY INSTRUCTIONS
1.
Unscrew three (3) locking screws from the bottom of the heater body (Figure 1) and save them.
2. Align two screw bosses and boss holes on back of two halves of base according to Figure 2.
3. Press two halves of the base, as in Figure 3, to interlock them together. (Figure 3)
4. Align power cord to the slot on the top side of the base. (Figure 4)
Secure the base to the heater body with the locking screws from Figure 1. Tighten the locking screws
. 5
firmly with a screw driver. (Figure 5)
Figure 1
Figure 2
Figure 4
OPERATING INSTRUCTIONS
Operation
1.
Place the heater on a firm, level surface, after assembling per this manual. Plastic or rubber tabs, like the feet on
this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken,
stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or
hardwood floors.
1
6
5
Screw Bosses
Boss Holes
Figure 3
Figure 5
2. Plug the cord set into a 120 volts AC outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely
2
into receptacles, they may slip partially or completely out of the receptable with only the slight movement of the
attached cord. Receptables in this condition may overheat and pose a serious fire hazard; if covered by a curtain
3
or drape, the fire hazard is even greater.
3. When the heater is initially plugged in, there will be a "beep" and the Power Light will turn on indicating
power to the unit. The Power Light will remain lit until the heater is unplugged from the electrical outlet.
4. Turn the heater ON by pressing the Power Button
5. When turning the heater on, the unit will be in HIGH heat.
4
6. Press the
butto n to switch over LOW or HIGH heat.
7. To turn the heater OFF, press the Power Button
w
l l i
h s
t u
o d
w
n
0 3
s
c e
n o
s d
t a l
stopped.
Oscillation
Pressing the Oscillation Button
press the Oscillation Button
Timer Function
The timer function may be activated when the heater display is in any function. This function allows you to set
the length of time the heater will run before turning itself off, from 0 hour to 8 hours. Pressing the Timer Button
will increase the length of time by 1 hour each time this button is pressed. After the display reflects 8 hours, pressing
the
once more will reset the heater to run continuously. The heater will turn off when the set time
i T
m
r e
B
t u
o t
n
has el
apsed. The unit can be turned back on by pressing the Power Button
to 0 hour will cancel the timer function.
Automatic Temperature Control
1.
To set the room at a specific temperature, press the Temperature Setting Button
or
buttons to the desired temperature. The heater is now in Auto Temperature Mode and the
glow on the LED display.
2. Press the
and
buttons at the same time for two seconds to change the display to show the temperature
reading in Celsius. Press the same two buttons together again to change the display back to show the
temperature reading in Fahrenheit.
3.
When the display shows the temperature at which you want to set the unit, the set temperature will flash
several time. The display will return to indicate the current room temperature and will gradually change as the
room temperature changes.
.
. The unit will first turn off the heating elements, the fan
. r e
U
p n
u l
t g
e h
u
t i n
y b
u p
n i l l
t g
e h
l p
g u
o r f
m
t
e h
will allow the heater to oscillate back and forth. To stop the oscillation,
again.
e
e l
r t c
a c i
o l
t u
t e l
n o
y l
a
e t f
r the fan
. Pressing the Timer Button
, then press the
A
indicator will
Tabla de contenido
