Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

PRIMEX
SUBMERSIBLE LEVEL TRANSMITTER
®
INSTALLATION INSTRUCTIONS
ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing this
product. A qualified service person must install and
service this product according to applicable electrical
and plumbing codes.
Failure to follow these precautions could result in serious injury or death. Replace product immediately if cable becomes damaged
or severed. This product must be installed in accordance with National Electric Code, ANSI/NFPA 70 so as to prevent moisture from
entering or accumulating within boxes, conduit bodies, fittings, or cable. Keep these instructions after installation.
IMPORTANT INFORMATION
Applications: sewage and effluent lift stations, stormwater pump stations, non-potable water systems,
tanks, wet wells, and reservoirs.
Primex
recommends the use of a desiccant filter or bellows to protect against moisture entering the
®
vent tube.
Do not bend cable to a radius smaller than 1.5 inches (38mm) to avoid kinking the vent tube.
When installing, lower the transmitter slowly and avoid impact with objects in the wet well.
Do not press against the transmitter diaphragm with a sharp object.
STABILIZING WEIGHT
Each PSLT is provided with a removable stabilizing weight. The stabilizing weight must be attached to the
transmitter housing prior to installation. Hand tightening is adequate.
Step 1
Step 3
(PSL T)
30° - 40°
EXPLOSION OR FIRE HAZARD
Do not use this product with flammable liquids.
Do not install in hazardous locations as defined by
National Electrical Code, ANSI/NFPA 70.
Step 2
Step 4
1
Tabla de contenido
loading

Resumen de contenidos para Primex 1050714

  • Página 6: Transmisores De Nivel Sumergibles Primex

    TRANSMISORES DE NIVEL SUMERGIBLES PRIMEX (PSL T) ® INSTRUCCIONES DE INSTALACIÓN PELIGRO DE CHOQUE ELÉCTRICO PELIGRO DE INCENDIO O EXPLOSIÓN Desconecte el cable de alimentación antes de instalar este No utilice este producto con líquidos inflama- producto o de hacerle mantenimiento. La instalación y el bles.
  • Página 7: Soporte De Montaje

    SOPORTE DE MONTAJE El transmisor PLST trae un soporte de montaje en acero inoxidable y un conector de alivio de tensión para cables. Paso 1 Paso 2 Paso 3 Paso 4 Paso 5 (opción 1) Paso 5 (opción 2) 90°...
  • Página 8: Instalación

    En áreas de alta humedad, usar un tubo de secado (desecante) o fuelles para evitar la entrada de vapor de agua al tubo de venteo. Comunicarse con Primex para la información sobre órdenes de pedido. Nunca se debe terminar el cable del transmisor en una caja de conexiones en el pozo húmedo.
  • Página 9: Estación De Bombeo Característica Con Transmisor Yflotador De Respaldo

    ESTACIÓN DE BOMBEO CARACTERÍSTICA CON TRANSMISOR Y FLOTADOR DE RESPALDO CONDUCTO CONDUCTO DEL CABLE DEL CABLE DEL SENSOR DE LA BOMBA FLUJO DE ENTRADA DESCARGA FLOTADOR DE RESPALDO DE NIVEL ALTO FLOTADOR DE RESPALDO DE NIVEL BAJO BOMBA TRANSMISOR DE NIVEL CON PESA ESTABILIZADORA ADVERTENCIA:...
  • Página 10: Especificaciones

    Pesa estabilizadora: hierro fundido con recubrimiento epóxico, 0,45 kg (1,0 lb) 66 mm de diámetro x 64 mm de longitud (2,6” x 2,5”) NÚMERO DE PARTE DESCRIPCIÓN FECHA DE INSTALACIÓN 1050714 PSLT 16,7ftWC con cable de 50 pies 1050713 PSLT 16,7ftWC con cable de 75 pies 1050712...

Este manual también es adecuado para:

10507131050712105071710507161050715

Tabla de contenido