Silverline 234578 Manual De Usuario página 7

GB
Charging from 12V supply
1. Check that Positive and Negative Leads (2)+(5) are correctly stored
2. Plug the small plug of the12V Charging Lead (13) into the Charging
Socket (7)
3. Plug the large plug of the 12V charging lead into a suitable 12V DC
power socket (e.g. car cigarette lighter), check that the power supply
is switched on
• For the initial charge, allow 48-72 hours. For a normal recharge allow
8-10 hours
• This jump starter is equipped with an automatic safety cut-out to help
prevent damage from overcharging
IMPORTANT: Failure to follow the correct procedure when charging
batteries will result in permanent damage. You must follow the correct
procedure.
Using the jump starter
NOTE:
Always refer to vehicle handbook before using this product. If the
manufacturer specifies a particular sequence for jump starting, follow the
manufacturer's advice. Do not attempt to use this product on anything other
than 12V, negative earth, automotive charging systems.
1. Ensure that all vehicle accessory systems (headlights, radio, etc) are
switched off
2. Locate and identify positive, and negative, battery terminals. Batteries
are usually marked with a "+" near to the positive terminal, and a
"–" near to the negative terminal. If you are not completely sure of
which terminal is which, seek professional advice before using the
jump starter
3. If the battery terminals are corroded or dirty, clean them with a
suitable wire brush
4. Attach the (red) Positive Lead (2) to the positive battery terminal
5. Attach the (black) Negative Lead (5) to a clean part of the vehicle
chassis, or other sturdy metal part. Do not connect the clamp to any
part of the vehicle's fuel system
6. Check that the clamps are securely attached, and that they will not
come loose when the vehicle is started. Check that the leads are well
clear of all moving engine parts
7. Allow 1-2 minutes for the battery charge to stabilise
8. The battery should now be ready to start the engine. Run the starter
motor in short bursts (not more than 5 seconds). If the engine does not
start, allow another 2 minutes for the battery to charge, then repeat
9. Once the engine is running remove the Positive and Negative Leads
(2)+(5) from the battery terminals, taking care to avoid contact with
any moving or hot engine parts
10. Always recharge the jump starter fully each time it has been used.
Failure to keep the jump starter charged may cause permanent
damage to the internal battery
Using the air compressor
WARNING: Compressed air can be dangerous. Do not use this unit except
as directed and ensure that you are thoroughly familiar with all precautions
relating to the use of compressors and compressed air supply.
WARNING: Run compressor for max. 10 minutes continuously, then allow
10 minutes for the compressor to cool before using again
• Failure to follow these instructions may cause damage or explosion
• Always wear safety glasses or other eye protection
Inflating tyres
1. Check Compressor Switch (11) is in the OFF (0) position
2. Open access panel to rear housing and uncoil Compressor Lead (8)
3. Raise the locking lever on the connector into the vertical position
4. Press the connector firmly onto the tyre valve, then push down the
locking lever on the connector to lock the connector onto the valve
5. Push Compressor Switch (11) to ON (I) position. The pressure will be
displayed on the pressure gauge
6. Push Compressor Switch to OFF position when the required pressure
is reached and remove connector from tyre valve
REMEMBER: Never exceed 10 minutes continuous use; for every 10
minutes use, allow 10 minutes cool down period
6
Adaptors
• Three adaptors are supplied for inflating air beds, balls and other items
• To use, raise the locking lever on the connector
• Select appropriate adaptor and push the threaded end firmly into the
connector on the Compressor Lead (9). Lock in place by pushing the
locking lever down
12V power supply
• 12V appliances fitted with cigarette lighter type plugs can be connected
to the 12V Power Socket (10)
• Lift the rubber dust cover, and push the plug into the power supply socket
• Always return the 12V power switch to the "off" position when you have
finished using the appliance
Work light
• This jump starter is equipped with a Work Light (1)
• To switch the work light on, press the Work Light Switch (4). Press the
switch again to turn off
Maintenance
WARNING: Always ensure that the machine is disconnected from the mains
power supply before performing any maintenance procedure.
Cleaning
• Keep your jump starter clean. Always clean dust / particles away, and
never allow ventilation holes to become blocked. Use a soft brush, or dry
cloth to clean the machine. If available, blow through the ventilation holes
with clean, dry, compressed air
• Make sure that the positive and negative lead clamps are kept especially
clean. Dirty electrical contacts will severely impair the performance of
this product
Disposal
• Do not dispose of power tools, or other waste electrical and electronic
equipment, with household waste
• Contact your local waste disposal authority for information on the proper
way to dispose of tools