Tabla de contenido
Idiomas disponibles
Idiomas disponibles
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user's authority to operate the equipment.
SAfEty guiDELinES / DEfinitionS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should
always be followed to reduce the risk of personal injury. Improper operation, maintenance or
modification of tools or equipment could result in serious injury and property damage. There
are certain applications for which tools and equipment are designed. Black & Decker strongly
recommends that this product NOT be modified and/or used for any application other than for which
it was designed. Read and understand all warnings and operating instructions before using any tool or
equipment.
iMPoRtAnt SAfEty inStRuctionS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES READ ALL
INSTRUCTIONS
READ ALL INSTRUcTIoNS
WARNING: Read all instructions before operating product. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury.
• AVOID DANGEROUS ENVIRONMENTS: Don't use appliances in damp or wet locations. Don't use
appliances in the rain.
• KEEP CHILDREN AWAY. All visitors should be kept at a distance from work area.
• STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be stored indoors in dry,
and high or locked-up place – out of reach of children.
• DON'T FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the
rate for which it was designed.
• USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts.
Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear
protective hair covering to contain long hair.
• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with
side shields, complying with applicable safety standards and, when needed, a face shield. Also use
JUS300B_ManualENFRSP_062712.indd 2-3
2
face or dust mask if operation is dusty. This applies to all persons in the work area. Also use a hard
hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required.
Safety glasses or the like are available at extra cost at your local dealer.
• DON'T ABUSE CORD. Never carry appliance by cord or yank it to disconnect from receptacle. Keep
cord from heat, oil, and sharp edges.
• DON'T OVERREACH. Keep proper footing and balance at all times.
• DISCONNECT APPLIANCES. Disconnect the appliance from the power supply when not in use,
before servicing, and when changing accessories such as blades and the like.
• AVOID UNINTENTIONAL STARTING. Don't carry plugged-in appliance with finger on switch. Be sure
switch is off when plugging in.
• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or
outlets to be used. Receptacles are available having built in GFCI protection and may be used for this
measure of safety.
• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not
recommended for use with this appliance could be hazardous. Note: Refer to the accessory section
of this manual for further details.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are
tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function. A part that
is damaged should be properly repaired or replaced by manufacturer unless otherwise indicated
elsewhere in this instruction manual. Have defective switches replaced by manufacturer. Do not use
tool if switch does not turn it on and off.
• DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive
atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended
for use outdoors and so marked.
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt,
use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAGE FOR CORD SETS
Volts
Total Length of Cord in Feet
120V
0-25
(0-7.6m)
240V
0-50
(0-15.2m)
Ampere Rating
0'-25'
More
Not more
Than
Than
0 -
6
18
6 -
10
18
10 -
12
16
12 -
16
14
WARNING: BURST HAZARD: Do not use the unit for charging dry-cell batteries that are commonly
used with home appliances. These batteries may burst and cause injury to persons and damage
property. Use the unit for charging/boosting a LEAD-ACID battery only. It is not intended to supply
power to a low-voltage electrical system other than in a starter-motor application.
WARNING: SHOCK HAZARD:
• If an extension cord is used, make sure that:
a) the pins of extension cord are the same number, size and shape as those in the charger,
26-50
51-100
101-150
(7.6-15.2m)
(15.2-30.4m) (30.4-45.7m)
51-100
101-200
201-300
(15.2-30.4m) (30.4-60.9m) (60.9-91.4m)
Extension Cord Length
26'-50'
51 '-100 '
101' -150 '
American Wire Gage (AWG)
16
16
14
16
14
12
16
14
12
12
Not Recommended
3
6/27/2012 11:18:21 AM
Tabla de contenido
