Idiomas disponibles
Idiomas disponibles
Ordering part #
CHFE 007
4 x
1 x
Sheet nr.
ALLEN KEY
Ordering part #
VTAC 052
4 x
2 x
Item #
9
Ordering part #
VTAC 174
4 x
1 x
Item #
4
Ordering part #
PDPL 028
5 x
1 x
Item #
15
9
8
4
9
13
6
1
Fig. 1
4
Fig. 2
Note: Use two people to assemble this unit.
Ordering part #
PDPL 021
IMPORTANT: During assembly leave some movement in the legs before fully tightening all screws.
Item #
10
1. SELECT the BOTTOM frame (1), with the threaded metal inserts on the bottom, and SCREW the
Ordering part #
leveling feet (2) into the inserts.
PDPL 030
Item #
2. PLACE the BOTTOM frame (1) on the floor with the leveling feet (2) facing the front. POSITION the
2
RIGHT side leg (3) over the BOTTOM frame, with the Bell'O
Ordering part #
CAREFULLY tip both pieces over. SECURE them together with one long screw (4). DO NOT FULLY
FVPL 005
TIGHTEN AT THIS POINT.
Item #
12
3. INSERT the square center shelf support bar (5) into the cutout in the center of the RIGHT side leg
Ordering part #
(3). INSERT the opposite end into the left side leg (6).
FVPL 008
Item #
4. PLACE the left leg (6) over of the BOTTOM frame (1) and SECURE the left side leg to the BOTTOM
14
frame with one long screw (4). DO NOT FULLY TIGHTEN AT THIS POINT.
17
4
7
15
10
5
4
2
14
14
12
Fig. 3
English
5. Turn the unit upright with the BOTTOM frame (1) on the floor and the leveling feet (2)
facing forward. POSITION the TOP frame (7) upward with the threaded inserts in the
curved frame side facing the rear. PLACE the TOP frame (7) into the cut out slots in
the leg ends. SECURE the TOP frame to the legs with long screws (4). DO NOT FULLY
TIGHTEN THE SCREWS AT THIS POINT.
6. PLACE the bowed side of the CMS
the rear of the frame with the two holes in the top facing upward. ALIGN the top
18
and bottom holes of the CMS
the TOP and BOTTOM frames (1) & (7). SECURE the CMS
short bolts (9).
IMPORTANT: Make sure that the legs are straight and aligned with the square
center shelf support bar (5) before final tightening or the center glass shelf may be
difficult to insert.
13
NOW TIGHTEN ALL SIX SCREWS FULLY.
7. MOVE the furniture to the location it will occupy in the room when fully
3
assembled and in use.
8. INSERT the plastic leg caps (18) into the legs (3) and (6). APPLY smaller rubber
glass pads (10) to the upper side of the BOTTOM frame (1) as shown.
9. SLIDE one smaller shelf (11) onto the BOTTOM frame (1) with the hole inserted
11
12. PLACE the top shelf (17), with the SILVER DISCS, onto the top
frame and TOP holes of the CMS
(17) to the CMS
13. ADJUST the leveling feet (2) to ensure that the furniture is level and
resting flat on the floor.
IMPORTANT: REMOVE ALL GLASS, TV AND OTHER EQUIPMENT FROM
THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT. DO NOT
ATTEMPT TO MOVE THE ASSEMBLED FURNITURE AFTER THE GLASS
SHELVES HAVE BEEN INSTALLED, AND/OR WHEN THERE IS EQUIPMENT
LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELVES TO
BECOME UNSECURE AND FALL. MAKE SURE THAT THE FRONT OF THE TV
IS POSITIONED A FEW INCHES BACK FROM THE FRONT OF THE TOP GLASS.
WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT AND LEVEL
SURFACE. ALWAYS PLACE THE HEAVIEST EQUIPMENT ON THE BOTTOM SHELF.
®
logo at the top and facing forward.
®
(Cable Management System) post (8) against
®
post with the threaded inserts on the rear sides of
through the bottom slot of the CMS
glass shelf in place with the 'T' shaped plastic shelf
locking pin (12).
10. SLIDE the second smaller shelf (11) over the
square shelf support bar (5) and through the
slots (13) on the center of the side legs (3) and
11
(6), with the hole inserted through the slot of
the CMS
®
post (8). LOCK the shelf in place
with the 'ROUND' Spiral pin (14) and turn
until the shelf is secure using the Allen key.
DO NOT OVERTIGHTEN.
11. APPLY the larger rubber glass pads (15) to the
TOP frame (7) and to the outer front frame curve
as shown.
®
post (8). SECURE the TOP shelf
®
post with 2 smaller screws (9).
®
to the frames with the
®
post (8). LOCK the
