Tabla de contenido
GB
Workbench
INTRODUCTION
• The Slide and Lock system works in an entirely different
way from all other conventional clamping systems
• Read this instruction manual carefully before use and
save it for future reference 1
• Only use the parts and accessories supplied; damage
due to the use of non-original parts and accessories will
be excluded from the warranty
• This workbench is not intended to be used for
clamping electrical power tools
TECHNICAL SPECIFICATIONS 2
WORKBENCH PARTS 3
A Clamping handle
B Adjustable clamping jaw
C Support arm (max. 5 kg)
D In-between clamping block
E Fixed clamping jaw
F Worktop clamping block
G Unlocking lever
SAFETY
• Ensure that the workbench stands on a fi rm and non-
slippery surface
• Do not place heavy objects on the edge to prevent the
workbench from turning over 4
• Do not attempt to climb onto or stand on the
workbench 5
• Never load the worktop with more than 200 kg 6
• Place heavy objects calmly on the workbench; do not
drop them 7
• Keep children away from work area
• Store the workbench indoors in a dry and locked-up
place, out of reach of children
USE
• Assembly instructions 8
- the sequence of the numbers appearing in the
drawing corresponds with the sequence of the steps
to be followed for assembling the workbench
! firmly tighten all screws and nuts
• Operating instructions 9
1
turn both clamping handles A counter-clockwise as
far as they will go (between 1 to 6 turns)
2
push adjustable clamping jaw B back as far as it will
go
3
fold out both support arms C for optimal workpiece
support
4
hold the workpiece with one hand between the jaws
(ensure that the 4 in-between clamping blocks D
are correctly aligned to the workpiece)
0950
5
pull adjustable clamping jaw B with the other hand
towards the workpiece and fi xed clamping jaw E
6
carefully tighten each clamping handle with less than
one turn (mostly less than half a turn)
- for releasing the workpiece simply turn each
clamping handle back into the downward position
! never try to fine-adjust the clamping jaws by
turning the clamping handles counter-clockwise,
because this always results in releasing the
clamping jaws
- repeat steps 1 through 6 for every new clamping
procedure
• In-between clamping blocks 0
- always use the in-between clamping blocks to
prevent the aluminium from damage
! ensure that the workpiece is securely clamped
• Worktop clamping blocks !
! ensure that the workpiece is securely clamped
• Folding out the workbench @
• Collapsing the workbench #
- push lever G downward for unlocking the workbench
SERVICE
• If the workbench should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the workbench undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram are listed on www.skileurope.com)
F
Etabli
INTRODUCTION
• Le système de glissière et de verrouillage fonctionne
tout à fait différemment des autres systèmes de serrage
conventionnels
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'appareil et conservez-le pour pouvoir vous y
référer ultérieurement 1
• Utilisez uniquement les pièces et accessoires fournis;
les dommages résultant de l'utilisation de pièces et
accessoires n'étant pas d'origine seront exclus de la
garantie
• Cet établi n'a pas été conçu pour être utilisé pour le
serrage d'outils électriques
SPECIFICATIONS TECHNIQUES 2
9
0950
Tabla de contenido
