Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation instructions for part 95-7017B
Mitsubishi Lancer 2002-2007
KIT FEATURES
• Double DIN radio provision
• Painted matte black
KIT COMPONENTS
• A) Radio trim panel • B) Brackets • C) Climate control re-location panel • D) (6) speed clips
• E) (6) #10 x 1/2" screws • F) (2) #8 x 1/2" screws • G) (2) #10 flat washers
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7001 • 70-7003
Antenna Adapter: • Not required
METRA. The World's best kits.
95-7017B
C
D
1-800-221-0932
™
Dash Disassembly
– Mitsubishi Lancer 2002-2007 ...........................2-4
Kit Assembly
– Double DIN radio provision ................................5-6
TOOLS REQUIRED
• Phillips screwdriver • Panel removal tool
• Socket wrench
E
F
G
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
metraonline.com
Table of Contents
© COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
Tabla de contenido
Manuales relacionados para Metra 95-7017B
Resumen de contenidos para Metra 95-7017B
- Página 1 Installation instructions for part 95-7017B Table of Contents Mitsubishi Lancer 2002-2007 95-7017B Dash Disassembly – Mitsubishi Lancer 2002-2007 ......2-4 Kit Assembly – Double DIN radio provision ........5-6 KIT FEATURES • Double DIN radio provision • Painted matte black KIT COMPONENTS TOOLS REQUIRED • A) Radio trim panel • B) Brackets • C) Climate control re-location panel • D) (6) speed clips • Phillips screwdriver • Panel removal tool • E) (6) #10 x 1/2” screws • F) (2) #8 x 1/2” screws • G) (2) #10 flat washers • Socket wrench CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation.
-
Página 2: Dash Disassembly
95-7017B Dash Disassembly 1. Remove (2) Phillips screws securing the panel below the steering column then unclip and remove the panel. (Figure A) 2. Squeeze the sides of the glove box and pull down then back to remove the box. (Figure B) 3. Pull the knobs from the climate controls and remove 2 Phillips screws from behind them. (Figures C, D) (Figure A) (Figure C) Continued on next page (Figure B) (Figure D) - Página 3 95-7017B Dash Disassembly 4. Unsnap and remove the climate control trim panel. (Figure E) 5. Remove (4) Phillips screws securing the radio then remove it. (Figure F) 6. Remove (2) Phillips screws facing up from the lower dash pocket or factory CD changer (if equipped) then unclip and remove the pocket. (Figure G) Continued on next page (Figure E) (Figure G) (Figure F)
- Página 4 95-7017B Dash Disassembly 7. Remove (4) Phillips screws and (8) 10mm bolts to remove the sub-dash bracket (this bracket will come out of the dash in four pieces). (Figures H and I). Tip: With the knee bolster panel and the glove box removed you can gain access to the sub dash brackets easier. 8. Remove (6) panel clips from the factory radio panel and keep for assembly. 9. Remove the (2) panel clips from the pocket or cd changer trim panel and keep for assembly. Continue to kit assembly...
-
Página 5: Kit Assembly
95-7017B Kit Assembly Double DIN radio provision 1. Cut a notch in the sub dash on the plastic supports to allow for clearance of the climate control in its new position. (Figures A,B) 2. Attach the (2) panel clips to the climate control relocation panel. (Figure C) 3. Attach the climate control to Left side the climate control relocation panel with the (2) factory screws (Figure A) (removed in step 3 in disassembly) and the provided (2) #8 x 1/2” Phillips screws and the (2) #10 flat (Figure C) washers. (Figure C) 4. Install the climate control/ relocation panel assembly into the pocket location in the dash using the factory hardware removed in disassembly. (Figure D) Continued on next page... - Página 6 95-7017B Kit Assembly Double DIN radio provision 5. Attach the (6) panel clips (removed in step 8 of disassembly) to the radio trim panel. (Figure E) 6. Attach the brackets to the radio using the screws supplied with the radio. (Figure F) 7. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect (Figure E) the negative battery terminal and test the unit for proper operation. 8. Attach the (6) speed clips to the sub dash in the radio opening. (Figure G) (Figure G) 9. Secure the aftermarket radio/ bracket assembly in the sub dash using the provided (6) #10 x 1/2” Phillips screws. 10. Snap the radio trim panel over the aftermarket radio. (Figure F)
- Página 7 95-7017B Notes...
- Página 8 Installation instructions for part 95-7017B NOWLEDGE IS OWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
-
Página 9: Herramientas Requeridas
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 95-7017B Indice Mitsubishi Lancer 2002-2007 95-7017B Desmontaje del tablero – Mitsubishi Lancer 2002-2007 ......2-4 Ensamble del kit – Provisión de radio doble DIN .......5-6 CaraCterístiCas deL kit • Provisión de radio doble DIN • Pintura negro mate Herramientas requeridas CaraCterístiCas deL kit... -
Página 10: Desmontaje Del Tablero
95-7017B Desmontaje del tablero 1. Quite los (2) tornillos Phillips que sujetan el panel debajo de la columna de dirección, luego desenganche y quite el panel. (Figura A) 2. Presione los lados de la guantera y jale hacia abajo y arriba para quitar la guantera. - Página 11 95-7017B Desmontaje del tablero 4. Desenganche y quite el panel de la moldura del control de clima. (Figura E) 5. Quite los (4) tornillos Phillips que sostienen el radio, luego quítelo. (Figura F) 6. Quite los (2) tornillos Phillips orientados boca arriba desde la cavidad del tablero inferior o el cargador de CD de fábrica (si está...
- Página 12 95-7017B Desmontaje del tablero 7. Quite los (4) tornillos Phillips y los (8) pernos de 10 mm para quitar el soporte del sub tablero (este soporte saldrá del tablero en cuatro piezas). (Figura H,I) SUGERENCIA: Al quitar el panel del protector de rodillas y la guantera, puede tener acceso más fácil a los soportes del sub...
-
Página 13: Ensamble Del Kit
95-7017B Ensamble del kit Provisión de radio doble DIN 1. Corte una muesca en el sub tablero sobre los soportes de plástico para dejar un espacio libre para la nueva posición del control de clima. (Figura A) 2. Coloque los (2) ganchos del panel en el panel de reubicación del... - Página 14 (Figura F) 7. Localice el arnés de cables de fábrica en el tablero. Metra recomienda el uso de un adaptador adecuado de acoplamiento de Metra o de AXXESS. Vuelva a conectar la (Figura E) terminal negativa de la batería y pruebe...
- Página 15 95-7017B Notas...
- Página 16 INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 95-7017B EL CONOCIMIENTO ES PODER NOWLEDGE IS OWER Mejore sus habilidades de instalación y fabricación Enhance your installation and fabrication skills by inscribiéndose en la escuela de dispositivos electrónicos enrolling in the most recognized and respected mobile electronics school in our industry.