Idiomas disponibles
Idiomas disponibles
Since 1956
• DO NOT USE ON LIVE CIRCUITS. DISCONNECT POWER. Metal tip on rod.
• Wear safety glasses and gloves.
• Keep rod inside reel when not in use. Out-of-control rod can harm personnel or property.
• Keep rod clean. Some contaminants (including water) can conduct electricity.
• Keep secure footing. Protect yourself from falling should pulling eye move suddenly or separate from rod.
• Check for rod damage prior to use. Cracks, gouges, nicks, or white stress marks on jacket or sharp bends will weaken rod.
Injury could result if rod breaks while pulling.
• Do not use slip joint pliers, locking pliers or powered pulling equipment on rod.
• Do not force a pull that is stuck. Remove wires and check for kinks or obstructions.
• Avoid pulling rod over sharp edges.
• Do not bend rod beyond 7" radius.
Read manufacturer's instructions before using adhesive. In case of eye contact, flush with water and seek medical atten-
tion If skin contact occurs, apply solvent (such as nail polish remover) to area and gently remove adhesive. Wash solvent
off with water. Solvents should not be used in case of contact with eyes or open wounds.
Always wear safety goggles (ANSI Std. Z87.1) and gloves when working with adhesive and/or unprotected fiberglass rod.
See adhesive product label for Safety Data Sheet (SDS).
Part
Number
9-25-AK
9-139
9-141
11-142
9-143
9-148
9-25-12ST
Repair Kit
9-25-24ST
9-140
9-146
Jameson products carry a warranty against any defect in material and workmanship for a period of one year from date of shipment unless failure is due to
misuse or improper application. Jameson shall in no event be responsible or liable for modifications, alterations, misapplications or repairs made to its products
by purchaser or others. This warranty is limited to repair or replacement of the product and does not include reimbursement for shipping or other expenses
incurred. Jameson disclaims any other express or implied warranty.
OPERATION AND SAFETY MANUAL
WARNING - ADHESIVE
Accessories Sold Separately
End Ferrule, Splice Ferrule, Adhesive, Emery Cloth,
Accessory Kit
Canvas Pouch
Swivel Eye
Attach pull line or grip to freely rotating eye
Guides rod through bends, sweeps, misalignments,
Roller Guide
wires
Use with Swivel Eye for larger pulling loop to attach
Shackle Fitting
Pulling Eye. Must use 11-139 Swivel Eye.
Connect two rods when single length is not long
Swivel Coupling
enough; provides rotation when pulling line, wire
or rope.
Rod Grapples
Connects two rodders from opposite directions
12" Stinger Tip
Guide rod through bends, sweeps, misalignments
24" Stinger Tip
Splice Repair Kit
Splice Ferrule, Adhesive, Emery Cloth, Instructions
End Ferrule Repair
End Ferrule, Adhesive, Emery Cloth, Instructions
Warranty
Part Number
Buddy® Model
9-25-300M
300' X 3/8" Good Buddy
9-25-400M
400' X 3/8" Good Buddy
Swivel Eye
Roller Guide
Swivel Coupling
Shackle Fitting
Stinger Tip
Grapples
GB_MO3
Tabla de contenido
Resumen de contenidos para Jameson 300' X 3/8” Good Buddy
- Página 1 Warranty Jameson products carry a warranty against any defect in material and workmanship for a period of one year from date of shipment unless failure is due to misuse or improper application. Jameson shall in no event be responsible or liable for modifications, alterations, misapplications or repairs made to its products by purchaser or others.
- Página 2 Using The Good Buddy® Assembly 1. Spread frame apart until fully open on level surface. 2. Unscrew ball knob mounted on reel until 3/8” of thread is showing. 3. Insert pivot axle on frame into elbow. 4. Hold reel in vertical or horizontal position. NOTE: Never face open side of reel when in horizontal position. 5.
- Página 3 Using The Good Buddy® Operation 1. Identify both ends of conduit. Ensure switch gear or other components in area will not be damaged by rod entering vault or box. 2. Insert rod through safety feed guide. Failure to do so can cause a hazardous condition. 3.
- Página 4 Splicing Rod Or Attaching New End Ferrule 1. Cut away damaged section(s) of fiberglass rod with a fine-tooth hacksaw or sharp knife. Strip protective jacket back about 1-1/18” for end ferrule repair or 1” for rod splice repair. Do not cut into fiberglass core when stripping jacket. Do not crush fiberglass core.
- Página 5 Garantía Los productos Jameson tienen una garantía contra cualquier defecto en el material y la confección por un período de un año a partir de la fecha de envío, a menos que la falla se deba a un uso indebido o una aplicación no autorizada. Jameson no se hará responsable en ningún caso de las modificaciones, alteraciones, aplicaciones indebidas o reparaciones hechas a sus productos por parte del comprador u otros.
-
Página 6: Ensamblaje
Cómo usar Good Buddy® II Ensamblaje 1. Despliegue el marco hasta que esté completamente abierto sobre una superficie nivelada. 2. Desenrosque la perilla redonda montada en la bobina hasta que se vean 3/8" de la rosca. 3. Introduzca el eje de pivote en el marco dentro del codo. 4. -
Página 7: Cómo Conectar Dos Guías Pasacables Con Grapas Para Recorridos Largos
Cómo usar Good Buddy® II Operación 1. Identifique ambos extremos del conducto. Asegúrese de que el interruptor y demás componentes en el área no se dañarán al introducir la varilla en la bóveda o caja. 2. Introduzca la varilla a través de la guía de alimentación segura. No hacerlo puede provocar una condición peligrosa. -
Página 8: Cómo Empalmar Varillas O Unir Un Nuevo Casquillo Terminal
Cómo empalmar varillas o unir un nuevo casquillo terminal 1. Corte las secciones dañadas de la varilla de fibra de vidrio con una sierra para metales de dientes finos o un cuchillo afilado. Quite aproximadamente 1-1/18" del re- vestimiento de protección para reparar el casquillo termi- nal, o 1"...