Idiomas disponibles
Idiomas disponibles
User Guide
IMPORTANT! READ AND FOLLOW
THESE INSTRUCTIONS CAREFULLY AND
KEEP FOR FUTURE REFERENCE.
Congratulations on the purchase of your new
Nomi High Chair. We believe that family meal
time is special; conversation, socialization, and
special moments all occur around the dining
table. With your new Nomi, you've made sure
that everyone is included, even the youngest
family members! In addition, your Nomi can be
accessorized with the Nomi Baby, Cushions,
and Tray, sold separately.
Assembly of the Nomi High Chair
Please find an assembly video at
www.evomove.com or on our YouTube channel.
The Nomi High Chair is assembled with the 6
supplied screws (H), using one of the 2 small
Allen wrenches (J2) you find stored under the
footrest (D), plus the large Allen wrench (J1)
you find in the hardware bag attached to the
bases (E).
IMPORTANT! Always use the supplied
TufLock
coated screws as they provide a
®
necessary strong grip. They are a little tough
to tighten, but once done they don't need to be
re-tightened as often.
Assemble on a level surface and start by at-
taching the base as shown in Figure 1 on page
1. Insert the long metal tube (I1) into the inside
bottom hole in one base and the short tube (I2)
into the top hole of the same base. Slide the
metal tubes into the wood stem (A) with the
wheel pointing backwards and then slide the
second base on. Insert 4 screws and use two
Allen wrenches to tighten the base to the stem.
Hold one screw with the small Allen wrench,
tighten the screw on the opposite side with the
large Allen wrench. Repeat on the second set
3
All manuals and user guides at all-guides.com
of screws. Insure there is no gap between the
stem and the bases. Tighten and re-tighten
all screws from both sides until all 4 screws
are secure. Retighten the screws 2-3 weeks
after assembly and when necessary.
Next attach the backrest (B) to the top of the
stem, and secure with the remaining 2 screws,
using the small Allen wrench. When finished,
store the 2 small Allen wrenches in the bottom
of the footrest for future tightening of the
screws.
Attach the footrest (D) and the seat (C) as
shown in Figure 1 on page 1, following the
instructions below.
IMPORTANT! The adjustment knobs (F) need
to be carefully attached to the bolts on the
seat and footrest. Prior to shipping, they are
attached, inspected and correctly threaded.
To attach the footrest, unscrew the adjustment
knob, remove the plastic washer (G), and insert
the flat metal bolt through the track in the stem.
Place the washer back on the bolt with the
groove facing out, and very carefully thread
the knob onto the bolt using only your fingers.
Make sure it threads correctly. DO NOT use
force until you feel it is threaded correctly.
If need be, back it out and try again.
Repeat this step with the seat, insuring it is
positioned all the way up on the stem. Make
sure the harness is still attached to the metal
bolt and pulled over the seat and lying flat
when tightening the knob, and it is not twisted.
Attaching the crotch restraint
The crotch restraint (K) MUST ALWAYS
BE USED with the seat in the top position!
Slide the lower part into the grooves on the
underside of the seat and push it all the way
in, Figure 2 on page 2. Align the tabs on the
crotch restraint and insert them into the slots in
the backrest, Figure 3 on page 2. Listen for the
audible click. Double check that it's locked
in place by pulling on the crotch restraint.
Always use the harness in combination
with the crotch restraint!
Using the Harness
The harness comes fully installed on the seat
on the Nomi High Chair. The 5 point harness
uses a puzzle system to interlock the shoulder
and waist straps before snapping them into the
crotch buckle. Make sure to adjust the straps
of the harness to fit securely around your child.
Always use the harness in combination
with the crotch restraint!
Adjusting the footrest
Adjust the position of the footrest by turning
the adjustment knob to loosen. The footrest is
at the correct level when the child's feet are flat
and their knees are at a 90° angle, Figure 4B
on page 2.
As your child grows
When the child is at least 2 years old AND has
developed the ability to climb in and out of the
chair on their own, AND can also sit safely
unrestrained, the crotch restraint and harness
can be removed for use in the Toddler Seat
mode.
EN
Removing the crotch restraint and harness
IMPORTANT! Never use the harness without
the use of the crotch restraint attached.
To remove the crotch restraint simply press
on the tabs behind the backrest and push out.
Slide the crotch restraint off the seat. In order
to remove the harness, remove the seat from
the wood stem. Turn the seat upside down and
remove the end of the crotch strap from the
hooks. Next, simply slide the harness off of
the metal bolt.
Adjusting the seat and footrest
Adjust the height of the seat and footrest by
turning the two knobs to loosen. Adjust the
seat height first. The seat height is correct
when the child sits in the chair with their
elbows at tabletop level while holding the arms
close to the body, Figure 4A on page 2. The
footrest is at the correct level when the child's
feet are flat and their knees are at a 90° angle,
Figure 4B on page 2.
Removing the base extensions
When the child has reached the age of 3
years, the base extensions can be removed, if
desired, by simply unscrewing the plastic bolts
holding them in place.
Holds an adult
The Nomi is tested up to 330 lbs (150 kg), so it
is strong enough for full size adults as well.
4
