Advanced Programming; Monitor Settings; Wiring Diagram - golmar Tekna HF Gtwin Guía Rápida

ADVANCED PROGRAMMING

Continued from previous page
- Exiting programming mode:
To exit 'programming mode,' press button
1 short and 2 long audible tones will confirm this and the programming
LED will turn off, indicating that button
Note: When exiting programming mode, if 'doctor mode' has been activated, the
monitor's programming LED will blink slowly (green), see p. 1.

MONITOR SETTINGS

SW1 configuration switch:
DIP 1: This defines the operating mode of the monitor - OFF 'Hands-free' (factory
default)/ON 'Push-to-talk.'
DIP 2 to DIP 8: To configure the desired code (2 = most significant
bit and 8 = least significant bit).
Below is an example of a site with 22 apartments:
EL632/GTWIN
Code Monitor
/telephone
ON
C.126 C. 00
1 2 3 4 5 6 7 8
ON
C. 10 C. 09
1 2 3 4 5 6 7 8
ON
C. 08 C. 07
1 2 3 4 5 6 7 8
EL60 D 6
ON
C. 06 C. 05
1 2 3 4 5 6 7 8
ON
C. 04 C. 03
1 2 3 4 5 6 7 8
ON
C. 02 C. 01
1 2 3 4 5 6 7 8
EL610D
ON
C. 20 C. 19
1 2 3 4 5 6 7 8
ON
C. 18 C. 17
1 2 3 4 5 6 7 8
ON
C. 16 C. 15
1 2 3 4 5 6 7 8
ON
C. 14 C. 13
1 2 3 4 5 6 7 8
ON
C. 12 C. 1
1 2 3 4 5 6 7 8
SW2 configuration switch:
INT: Define the internal code of the monitor/telephone in order to set it as master,
slave 1, slave 2 or slave 3 using the SW2 switch with a code from 0 to 3
respectively.
ON ON ON
1 2 1 2 1 2
( ) *
( )
Factory setting. INT 0 INT 1 INT 2
*
Important: For optional programming, optional connections and more
information, see the TTEKNA HF GTWIN manual (code 50120254).
https://doc.golmar.es/search/manual/ 5012 0254

WIRING DIAGRAM

4
O
ne building with 1 column of up to 127 monitors and 1 main video
panel (buttons).
for more than 5 seconds,
J2
can be released.
End of
MASTER
line
MONITOR O (Z) N
SW2
ON
1 2
INT 0
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
ON
1 2
INT 0
SW1 SW2
1 2 3 4 5 6 7 8 9 10 1 2
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
ON
1 2
INT 0
J2
End of
MASTER
line
MONITOR
Code Monitor
O (Z) N
SW2 /telephone
ON
ON
1 2
1 2 3 4 5 6 7 8 INT 0
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
( ) Remove the jumper from all of the
*
ON
distributors except the last.
1 2 3 4 5 6 7 8
To configure the SAV-GTWIN call
1 ( )
ON
repeater, see the TTEKNA HF GTWIN
1 2 3 4 5 6 7 8
manual, p. 18.
ON
( ) To connect the FA-Gtwin power
2
1 2 3 4 5 6 7 8 supply to the filter and line
protector, see the TGTWIN SYSTEM
MANUAL, p. 44.
ON
( ) 3
To connect the secondary AC lock
1 2 3 4 5 6 7 8
release (Golmar), see the TGTWIN
ON
SYSTEM MANUAL, p. 45.
1 2 3 4 5 6 7 8
Main panel
ON
Video door
entry system
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1
1 2 3 4 5 6 7 8
( ) SE2
3
ON
Lock release
max. 12 Vdc/270 mA.
Remember: Button panel up to 122 apartments.
1 2
Important: For further information about the door panel, sections,distances,
INT 3
wiring diagrams, etc., see the TGTWIN SYSTEM MANUAL, code 50122345).
https://doc.golmar.es/search/manual/5012
COLUMN
DISTRIBUIDOR
LINE OUT D4L-GTWIN
LINE LINE
LINE IN LINE IN
3 4
Apartment
LINE OUT LINE OUT
Apartment
( )
Z=ON
CP front *
front CP
door
door call
S+
S+
call
S- S-
LINE LINE
LINE IN
LINE IN
1 2
Apartment
LINE OUT
LINE OUT
LINE IN
Apartment
CP front
front CP
door
S+ door call
S+
S-
call
S-
TO THE FOLLOWING DISTRIBUTORS
D4L-GTWIN
DISTRIBUTOR
LINE OUT
LINE LINE
LINE IN LINE IN
3 4
LINE OUT Apartment Apartment LINE OUT
Z=OFF
CP front
front CP
door
door call
S+
S+
call
S- S-
LINE LINE
LINE IN
LINE IN 1 2
LINE OUT
Apartment
LINE OUT
LINE IN Apartment
CP
front
front CP
door
S+ door call
S+
S- call
S-
S+
S-
SAV-GTWIN
1 ( )
call repeater
LINE
Exterior door
PA
release button
LINE~
SP
NC CONTACT =
SE+
DOOR CLOSED
SE-
2345
5
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
Gtwin monitor
ON
1 2
INT 0
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
ON
1 2
INT 0
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
ON
1 2
INT 0
J2
End of
MASTER
line
MONITOR
O (Z) N
SW2
ON
1 2
INT 0
QUICK GUIDE
FA-GTWIN
POWER SUPPLY
( )
2
LINE 1
08940- Cornellá de Llobregat
LINE 2
230 Golmar se reserva el derecho a cualquier modificación sin previo aviso.
0
Golmar se réserve le droit de toute modification sans préavis .
Golmar reserves the right to make any modifications without prior notice.
Code 50120254 TTEKNA HF GTWIN EN GR REV.0319
[email protected]
Sistemas de comunicación S.A.
Tekna HF
GOLMAR S.A.
C/ Silici, 13
SPAIN
www.golmar.es