Tabla de contenido
OVERVIEW
Thank you for choosing the Invisia Serena-Seat. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your Invisia Serena-Seat is
properly assembled, installed, and cared for. Failure to follow instructions in
this manual could result in serious injury or death. If you are not equipped
to undertake the outlined work, we would recommend that you have your
Invisia Serena-Seat installed by a qualified contractor.
The Serena-Seat is a high quality, commercial grade, fold down shower
seat. The Serena-Seat is intended to provide shower seating support for
people with reduced mobility. The Serena-Seat is intended to bear weight
ONLY when the seat is in the down position; the seat is not intended to
bear weight in any other position. The Serena-Seat is intended to be folded
up when not in use. A friction hinge ensures that the handle will not
inadvertently lower when it is in the up position. The Serena-Seat is
installed with appropriate fasteners to a structural wall. The maximum user
weight for this product is 500lbs / 227kgs. Note: Product is not intended to
support full body weight (i.e. do not stand on the seat). The Serena-Seat is
not to be used in any other way than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
DELIVERY CONTENTS / PARTS
1. Seat Assembly
2. Bottom Wall Panel
3. Top Wall Panel
4. #10 x 3" Wood Screw, S/S (x8)
10
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC
REP
93123
FIGURE A.
INSTALLATION WARNINGS
1. Seat must be installed to walls that are structurally sound.
2. If desired installation location does not have adequate structure, add
wood blocking.
3. CAUTION - Do not install if structure behind walls is unknown.
4. CAUTION - Do not install into metal studs.
5. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength.
6. CAUTION - Do not use seat for purposes other than sitting.
7. CAUTION - Do not more seat more than 1 person at a time.
8. CAUTION - Gap between wood and aluminum frame.
9. CAUTION - Pinch points present when folding seat.
10. CAUTION - Seat and bathtub are slippery when wet.
SUGGESTED SERENA-SEAT LOCATIONS
To determine the optimal mounting location, we recommend consulting
with an appropriate healthcare professional. If side wall (to faucet) is less
than 36" / 914mm, seat can be mounted on the back wall. If side wall (to
faucet) is greater than 36" / 914mm, seat can be mounted on side wall
(less than 24" / 610mm from faucet wall). ADA recommend seat height
from finished floor 17-19" / 432-483mm.
INSTALLATION
1. Slide wall panels off of frame.
2. Mark the location on the wall of the top hole of the frame (to position the
seat surface at the required height).
3. Drill pilot hole for fastener.
4. Fasten the frame to the wall using appropriate fastener and
waterproofing.
5. Slide lower wall panel onto frame.
6. Use a level to ensure the seat is level and mark location on the wall of
top hole on the frame.
7. Drill pilot hole for fastener.
8. Fasten the frame to the wall using appropriate fastener and
waterproofing.
9. Slide lower wall panel off of frame.
10. Repeat step 7 and 8 for remaining holes (x6)
11. Slide wall panels onto frame.
12. Inspect hardware regularly, and tighten if required.
TECHNICAL DATA
Model
A
B
Back Rest
Seat
WS18
18.58"
17.96"
472mm
456mm
WS26
26.58"
25.96"
675mm
659mm
PRODUCT USAGE
See Figure F.
FIGURE B.
FIGURE C.
FIGURE D.
FIGURE E.
C
D
Hole Spacing
Overall Width
16.83"
19.84"
427mm
504mm
24.83"
27.84"
631mm
707mm
Tabla de contenido
