Leviton 47690-NFA Instrucciones De Uso

Notch Filter
Filtro de Ranura
Filtre d'absorption
1
A Division of Leviton Manufacturing Co.,Inc.
Phone: (425) 485-4288
Fax: (425) 483-5270
www.levitonvoicedata.com
47690-NFA
Instructions for Use
Notch FIlter
DESCRIPTION
Leviton's Notch Filter is used with the Leviton 3x8
Bi-Directional Video Amplifier (PN# 47690-38B). The Notch
Filter blocks out channels 75-80 in an existing NTSC cable
line-up, to make room for incoming signals, such as DVD,
satellites or cameras. Signals can then be modulated with
Leviton's Video Modulator (PN# 48210-DSM, PN# 48213-
VMA), connected to the 3x8 Bi-Directional Video Amplifier, and
viewed in the cable line-up of any television connected to the
system.
INSTALLATION
1. If incoming cable television service is already connected
to the CABLE IN connector on the 3x8 Video Distribution
module, disconnect it.
2. Screw the Notch Filter onto the CABLE IN connector of the
3x8 Video Module.
3. Connect incoming cable television service cable to the
other end of the Notch Filter.
4. Channels 75-80 will now be blocked out of the incoming
cable line-up, and replaced with whatever modulated
inputs are connected via the 3x8 Bi-Directional Video
Amplifier.
IMPORTANT INSTRUCTIONS
1. Read and understand all instructions. Follow all
warnings and instructions marked on the product.
2. Do not use this product near water—e.g., near a tub,
wash bowl, kitchen sink or laundry tub, in a wet base-
ment, or near a swimming pool.
3. Never push objects of any kind into this product through
cabinet slots, as they may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION
1. Never install communications wiring or components dur-
ing a lightning storm.
2. Never install communications components in wet loca-
tions unless the components are designed specifically
for use in wet locations.
3. Never touch uninsulated wires or terminals unless the
wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communica-
tions wiring or components.
5. To prevent electrical shock, each opening must be filled
with a module.
Notch Filter
Filtro de Ranura
Filtre d'absorption
1
A Division of Leviton Manufacturing Co.,Inc.
Phone: (425) 485-4288
Fax: (425) 483-5270
www.levitonvoicedata.com
47690-NFA
Instructions for Use
Notch FIlter
DESCRIPTION
Leviton's Notch Filter is used with the Leviton 3x8
Bi-Directional Video Amplifier (PN# 47690-38B). The Notch
Filter blocks out channels 75-80 in an existing NTSC cable
line-up, to make room for incoming signals, such as DVD,
satellites or cameras. Signals can then be modulated with
Leviton's Video Modulator (PN# 48210-DSM, PN# 48213-
VMA), connected to the 3x8 Bi-Directional Video Amplifier, and
viewed in the cable line-up of any television connected to the
system.
INSTALLATION
1. If incoming cable television service is already connected
to the CABLE IN connector on the 3x8 Video Distribution
module, disconnect it.
2. Screw the Notch Filter onto the CABLE IN connector of the
3x8 Video Module.
3. Connect incoming cable television service cable to the
other end of the Notch Filter.
4. Channels 75-80 will now be blocked out of the incoming
cable line-up, and replaced with whatever modulated
inputs are connected via the 3x8 Bi-Directional Video
Amplifier.
IMPORTANT INSTRUCTIONS
1. Read and understand all instructions. Follow all
warnings and instructions marked on the product.
2. Do not use this product near water—e.g., near a tub,
wash bowl, kitchen sink or laundry tub, in a wet base-
ment, or near a swimming pool.
3. Never push objects of any kind into this product through
cabinet slots, as they may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION
1. Never install communications wiring or components dur-
ing a lightning storm.
2. Never install communications components in wet loca-
tions unless the components are designed specifically
for use in wet locations.
3. Never touch uninsulated wires or terminals unless the
wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communica-
tions wiring or components.
5. To prevent electrical shock, each opening must be filled
with a module.