Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AX-ADTY01
Amped vehicles 2003-up
The AX-ADTY01 is designed to and must be used with the AX-ADBOX1 or
AX-ADBOX2 (sold seperately). Please refer to AX-ADBOX1 or AX-ADBOX2
for 16-pin connector instructions.
applIcatIons
leXus
ES330
2004-2006
ES350
2007-2010
ES300
2002-2003
GX470
2003-2008
IS350
2006-2010
IS300
2002-2005
IS250
2006-2010
LS460
2007-2008
LS430
2001-2006
LX470
2001-2007
RX300
2001-2003
RX330
2004-2007
RX350
2007-2009
RX400H
2006-2008
SC430
2002-2009
Interface components
22-pin harness to 20-pin Toyota harness with stripped leads
tools requIred
• Cutting tool • Tape • Crimping tool
• Connectors (i.e. butt-connectors, bell caps, etc.)
METRA. The World's best kits.
Installation Instructions for AX-ADTY01
toYota
4-Runner
2003-2011
Avalon
2011
Camry/Camry Hybrid
2010-2011
Corolla
2005-2010
Highlander
2008-2010
Prius
2010
Rav 4
2004-2010
Sequoia
2005-2011
Sienna
2004-2011
Solara
2004-2009
Tacoma
2005-2011
Tundra
2004-2011
Venza
2009-2010
Yaris
2007-2010
™
1-800-221-0932
Caution
Metra recommends disconnecting the negative battery terminal before
beginning any installation. All accessories, switches, and especially air bag
indicator lights must be plugged in before reconnecting the battery or
cycling the ignition.
*Note: Refer also to the instructions included with the aftermarket radio.
connectIons to Be made
from the 16-pin harness with stripped leads (included with interface)
• Connect the White wire to the left front positive speaker output of the aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of the
aftermarket radio.
• Connect the Gray wire to the right front positive speaker output of the aftermarket radio.
• Connect the Gray/Black wire to the right front negative speaker output of the
aftermarket radio.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the purple wire to the radio's right rear positive speaker output.
• Connect the purple/Black wire to the radio's right rear negative speaker output.
from the 20-pin toyota harness:
• Connect the Yellow wire to the radio's 12-volt battery or memory wire.
• Connect the Black wire to the radio's ground wire.
• Connect the Blue wire to the radio's antenna turn on wire of the aftermarket radio.
metraonline.com
(continued on next page)
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
Manuales relacionados para Axxess AX-ADTY01
Resumen de contenidos para Axxess AX-ADTY01
- Página 1 All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or The AX-ADTY01 is designed to and must be used with the AX-ADBOX1 or cycling the ignition. AX-ADBOX2 (sold seperately). Please refer to AX-ADBOX1 or AX-ADBOX2 for 16-pin connector instructions.
- Página 2 • Connect the White RCA to your aftermarket radio left AUX in (if equipped). • Connect the Red RCA to your aftermarket radio right AUX in (if equipped). • Plug in the ASWC-1 into the 12-pin harness of the AX-ADTY01 and refer to the ASWC-1 instructions.
- Página 3 El AX-ADTY01 está diseñado y DEBE utilizarse con el AX-ADBOX1 o AX-ADBOX2 (SE VENDE POR SEPARADO). Consulte el AX-ADBOX1 o AX-ADBOX2 para *NOTA: También consulte las instrucciones incluidas con el radio de obtener instrucciones para el conector de 16 pins mercado secundario.
- Página 4 (si incluye el equipamiento) • Conecte el conector RCA rojo a la entrada AUX derecha de su radio de mercado secundario (si incluye el equipamiento) • Conecte el ASWC-1 en el arnés de 12 pins del AX-ADTY01 y consulte las instrucciones de ASWC-1.