Idiomas disponibles
Idiomas disponibles
RELAY UNIT SAR-GB2
SAFETY PRECAUTIONS
( )
*
- Always disconnect the power supply before making modifications to the device.
.
- The fitting and handling of these devices must be carried out by
- The wiring must run at least 40 cm away from any other wiring
.
- Do not overtighten the screws on the terminal block.
- Install the relay unit in a dry and protected location free from the risk of dripping or splashing water.
- Install the SAR-GB2 relay unit and SAR-12/24 together with the FA-GB2A power supply unit.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- The maximum consumption of relay contacts shall not exceed from 2A to 30 Vdc/ 1.25A to 48 Vac.
- Before connecting the system to the mains, check the connections.
- Always follow the instructions contained in this manual.
CHARACTERISTICS
( )
*
GB2
- Digital relay for the
system, allows the following operating modes:
Stairs light activation relay (necessary module SAR-12/24).
O
Golmar additional alternating lock release relay (necessary power supply unit TF-104).
O
- Necessary to configure operating mode of the SAR-GB2 relay unit.
- Connects to the Bus
door
panel.
- Configuration DIP switch.
- Operating status LEDs.
- The maximum consumption of relay contacts will be from 2A to 30 Vdc (40w) / 1.25A to 48 Vac (40w).
- 12Vdc output to activate SAR-12/24 module in operating mode "stairs light activation".
OPERATING MODES
( )
*
Stairs light activation relay (necessary module SAR-12/24):
- This operating mode allows activation of the stairs light from the apartment.
It is activated through the push button
the monitor light function Vesta2
, Vesta7, Pentha
- See user manual for telephone or monitor installed in the apartment.
Mains
100~240Vac
Cn
FA-
GB /A
2
Bus Monitors
2
( ) 1
Neutral point of the power supply of the stairs light is
connected in series through the relay contacts of the
SAR-12/24.
IMPORTANT:
For the description, installation, configuration and programming of the system, see the corresponding manual.
( )
For more information, see the "TSAR-GB2 (code 50121952)" user manual.
*
https://doc.golmar.es/search/manual/50121952
authorised personnel
.
.
of the telephone T-562 GB2 or Nhea GB2 and from
or Thera.
To stairs light push button
220Vac/
( ) 1
1.8A max.
2
2
SAR-GB2
SAR-12/24
2
2
Access
door
panel
G 2
B
2
2
RELAY UNIT SAR-GB2
OPERATING MODES
( )
*
Additional lock release activation relay (necessary power supply unit TF-104):
- This operating mode allows activation of a Golmar additional alternating lock release. This lock
release is activated as lock release 1 or lock release 2 and with the panel that has been assigned
(through configuration in SAR-GB2) during a call or communication process.
It will be activated through the push button
telephone T-562 GB2 or Nhea GB2 and through the push button
the push button
for lock release 2 of the Vesta7 monitor) or through the menu for lock release 2
of the Vesta2
, Pentha
or Thera monitor (for lock release 2 it is necessary to enable function 2nd lock
release on
Vesta2
monitor, see user manual for the monitor installed in the apartment).
- See user manual for telephone or monitor installed in the apartment.
Mains
100~240Vac
Bus Monitors
( ) 1
The power supply of the lock release is connected in
series through the SAR-GB2 relay contacts.
IMPORTANT:
For the description, installation, configuration and programming
of the system, see the corresponding manual.
DESCRIPTION OF SAR-GB2 RELAY UNIT
( )
*
.
N.A
C N.C
12+
P AP
SAR-GB2
CONTACTOS RELE /
UNIDAD DE RELÉ
RELAY CONTACTS
RELAY UNIT
1,25 A 48 V ~ (Máx. 40w)
2 A 30 V
(Máx. 40w)
BUS
BUS
POWER IN-USE
.
INSTALLATION
( )
*
( )
Description of operation of dip switch SW1 and configuration of relay time.
*
( )
For more information, see the "TSAR-GB2 (code 50121952)" user manual.
*
https://doc.golmar.es/search/manual/50121952
or
(lock release 1 or lock release 2 respectively) of
for lock release 1 (or through
Additional
Va
c
Cn
lock release
2
2
FA-
GB /A
2
SAR-GB2
2
2
2
Access
a
a.
12Vdc and AP output connector.
b
b.
Relay contact connector.
c.
Label
d.
JP
e.
Status LED (power supply).
f.
c
Status LED (active).
g.
SW1 dip switch.
g
h.
DIN rail latch release.
d
e
h
f
The relay unit can be mounted onto a DIN rail
(4 elements) by applying slight pressure.
To remove the relay unit from the rail, use a flat
screwdriver and lever it off, as shown in the drawing.
.
N.A
C N.C
12+
P AP
SAR-GB2
CONTACTOS RELE /
UNIDAD DE RELÉ
RELAY CONTACTS
1,25 A 48 V ~ (Máx. 40w)
RELAY UNIT
2 A 30 V
(Máx. 40w)
BUS
BUS
POWER IN-USE
.
DIN 46277
3
( ) 1
TF-104
TF-104
Mains
100~240Vac
door
panel
G 2
B
2
.
jumper
(do not use)
.
