10.-Level meter:
The level meter shows the stereo output level
of Master output when CUE selector in Stereo mode. When CUE
selector in Split mode the left bargraph will show CUE level and
the right bargraph will depict Master level.
Controls independently from Master
11.-Booth level control:
an external amplifier. Please note that the level of this output will
not in any case be displayed on the level meter; consequently,
please check carefully for your amplifier not being overloaded.
12.-Master level control & Balance:
from Booth an external amplifier (main amplifier). The signal's
stereo balance can be controlled by means of control Balance
Master. This signal is displayed on the level meter.
13.-Mono/Stereo Selector:
normally stereo, in mono.
14.-Stereo/split-switch for headphones:
make you hear the preselected signal by means of CUE controls
in stereo, while position "split" will make you hear the CUE
preselected signal on one earcup and the Master output signal on
the other earcup.
15 Cue Pan: By means of this function, you can preview your
.-
forthcoming mix by crossfading between the preselected
headphones signal on the left side of the control and the Master
output signal (pre pot) on the
right
16.-Headphones level control:
connected, you may control the headphones volume. Please
check your headphones impedance for a minimum of 32 Ohms
and be aware of high-impedance headphones reducing the
maximum output power of this output, so that you should choose
a headphone with less than 200 Ohms of impedance.
Increases
6 dB
the level of low level frequencies
17.-Boost:
(100Hz). Use it to enhance the Beat.
18.-Crossfader:
Under the precondition of opened channel
faders of those channels being routed to the crossfader, you can
crossfade between these two input channels. To be in-field
replaceable, this part is front-detachable. For replacement,
switch off the unit and unscrew the 2 outer screws of the
crossfader and remove the part; detach the connector and replace
the part. Plug in the connector and screw the new part to the main
body again.
19.-Reverse:
Reverses the inputs right and left to the crossfader.
When in reverse mode a Led will light.
20.-Headphones connector:
headphones.
Controls independently
We can transform output signal,
Position "stereo" will
side of the control.
With a stereo headphone
Jack 6.3 stereo. Connect here the
DSPEFFECTS SECTION
21.- Master Automatic bpm (beat per minute) counter
display -
This sophisticated counter automatically calculates the
BPM of the signal at Master.
22.-Automatic (parameter/BPM Counter) info display -
sophisticated counter automatically calculates the BPM of any
audio source selected by means of the control Source switch
(28). Moreover, the display will differ with the setting of the
effect channel selector switch (27). The BPM for the source
selected with the effect channel selector knob (27) will be
displayed. Display will flash while BPM is being measured or
cannot be measured.
23.- Beat (Effect Synchronous Display/Beat Display)
display will differ with the setting of the effect selector switch
(27).
1. If
DELAY, ECHO, PAN or TRANS has been selected,
parameter for source BPM will be displayed in terms of a beat. It
will light if the beat is from 1/2 to 4/1. Pressing the effect beat
sync. button
(24)
will change beats clearing the display entirely. If
there is a disparity between the number of beats, the closest
number will be displayed blinking.
2. If FILTER, FLANGER has been selected, parameter for source
BPM will be displayed in terms of a beat. Pressing the effect beat
sync. button
(24)
entirely. If there is a disparity between the number of beats, the
closest number will be displayed blinking.
3. If PITCH has been selected, the extent of pitch adjustment will
be display.
24.- Effect beat sync. -
change in keeping with the BPM for source selected with the
effect source selector switch (28). The set value will change with
the effect selector switch (27) setting.
1. If DELAY, ECHO, PAN or TRANS has been selected,
parameter for source BPM will be set in terms of a beat (1/2 to
4/1).
2. IF FILTER, FLANGER has been selected, parameter for
source BPM will be set in terms of a number of beats (1/2 to 4/1).
3. IF DELAY or ECHO has been selected, the number of beats for
parameter cannot b
e set in excess of 2000 ms.
4. IF PITCH has been selected, settings of
0%, 50% and 100% will be possible.
25.- Parameter knob
of the built-in effector.
26.- Effects Depth Control
effected music versus de amount
27.- Effects selector switch
the music.
28.- Source Channel Selector switch -
to be effected.
29.- Effects Cue -
headphones the effected music.
30.- Effect on/off button -
selected source.
mcx
FUNCTIONS
will change the beat clearing the display
The value for effect parameter (25) will
-100%, -50%,
- Used to adjust the value of the parameters
- Used to adjust the amount of
of un
effected music.
- Used to select the effect to add to
Used to select the source
With these switch you replay on the
Engages the effect selected to the
This
- The
3
