Remote Control; Mute Button - KlipXtreme Charme Manual Del Usuario

Remote control

In addition to the panel controls, a remote control is included which provides additional functions to allow
greater control over the media player.
• Install the batteries in the remote control following the correct polarity as indicated inside the compartment.
(Requires two AAA batteries).
• In order for the remote to operate properly, ensure that it is pointed toward the front of the speaker.
1
2
3
4
5
6
7
8
Control
Cancels the audio coming from the speaker. Press it again to unmute
1.

Mute button

the speaker in all modes.
In USB/SD press this button briefly to play the previous track. Press and hold
TM
2.
this button to go backward fast.
In FM and Bluetooth
This feature is not available in Line In mode
Press this button to cycle through the different audio sources: FM, Bluetooth
3. Mode
USB and SD
TM
Use this button to activate the recording function when using the wired or wireless
4. REC button
microphone. Press it again to stop this function. Insert a USB or SD
the microphone prior to start recording. You can record from the external microphone,
Line in and FM input and save the recording to the storage device of your choice.
Enables the reverberation effect of the microphone. Use + or – to increase or
5. and 16. ECHO+/-button
decrease the effect.
Increases or decreases the bass (low) frequencies of the speaker.
6. Bass +/-
Scrolls through the different equalizer sound effects.
7. EQ
9
LED
ON/OFF
10
11
12
13
MODE VOICE REPEAT
14
15
REC REC PLAY R.DEL
16
17
ECHO ECHO+ M-PRI
- -
+ +
18
BASS TREBLE
+ +
EQ
MIC
19
VOL
VOL
- 0 -
1 2 3
20
4 5 6
7 8 9
Description
mode press it briefly to go to the previous channel or song.
®
modes. Press and hold this button to turn the voice prompt on or off.
8. Mic volume +/- button
9. LED ON/OFF
10.
11.
12. VOICE button
13. Repeat button
14. REC/Play button
15. R-DEL button
17. M-PRI
18. Treble +/- button
19. Vol +/-
20. Numbered keys (0 to 9)
IV. Initial setup
Note: For your safety, read this manual and follow all safety instructions before using the product.
Charging the battery
1. Plug the AC cable to a wall outlet.
2. When the unit is not in use or switched off, it will automatically recharge the internal battery as long as it
remains connected to utility power.
Powering on the unit
1. Turn the volume control on the top panel fully counterclockwise.
2. Connect audio input devices first. Make sure all input sources such as microphones, CD players, or digital
media players are turned off and volume settings are set to their lowest settings (zero).
3. Check that the loudspeaker voltage selector is set to the same voltage as the AC power outlet.
4. Then, connect the power cord to the loudspeaker and AC power outlet.
5. Slowly turn the volume clockwise until the sound output is at the desired level. If there is no sound, check
to make sure the source equipment is providing audio output.
V. Functionality
1. Auxiliary mode operation
Recommendation: An RCA to 3.5mm connector audio cable has to be used to enable audio playback from
devices fitted with an auxiliary 3.5mm jack.
, Line in,
®
a. First, connect the RCA portion of the cable to the RCA input of the speaker, then connect the other side of the
cable (3.5mm plug) to the source of choice. If the speaker is not set to the LINE IN mode, press the MODE
button to toggle through the different modes available until the preferred mode is found: Line In, Bluetooth®,
drive and connect
TM
USB, SD , FM.
TM
b. Start streaming audio files directly from the source of choice.
2. USB mode operation
a. First, connect a USB memory stick to the USB port of the speaker.
b. The speaker will detect the USB device and play the audio files. If the USB drive is not automatically
detected, press the MODE button to toggle through the different modes available until the preferred
mode is found: Line In, Bluetooth®, USB, SD
Increases or decreases the volume of the microphone.
Short press this button to activate the speaker from standby mode and vice
versa,press this button for three seconds to turn the LED lights on or off.
Press to start and pause media during Bluetooth
mode, press it to scan for channels. This feature is not available in Line In mode.
In USB/SD press this button briefly to play the next track. Press and hold this button
TM
to go forward fast. In FM and Bluetooth mode press it briefly to go to the next channel
®
or song. Note: The first time the speaker is used, press the
FM radio stations automatically. This feature is not available in Line In mode.
Use this button to filter the bass effect to make the sound clearer.
Use it to repeat a track or song in only in USB and SDTM modes. It has a single
repeat or repeat all function.
Press this button to play what was recorded in the USB memory device.
Use it to delete the files that have been recorded in the USB memory device.
Use it to give priority to the microphone. The music volume will decrease
automatically when the microphone is in use.
Adjusts the level of the high-frequency range.
It increases or decreases the volume level of the speaker. The volume can also be
controlled directly from each of the sources connected to the speaker.
In USB and SD modes, press any key from 0 to 9 on the remote to choose directly
TM
the tracks you want to play.
, FM.
TM
, SD or USB playback. In tuner
® TM
button to search available