Kobra 260TS Manual De Usario página 8

SHREDDING CD/DVD/CREDIT CARDS
(All models except for HS High Security models)
Insert the optical media into the throat of the machine (2A),the
light bar (P) comes on and the machine starts up automatically
thanks to the electronic eyes located on the inside of the throat
(2A) which detect the presence of material to be shredded and
automatically stop the cutting blades a few seconds after
shredding is finished.
The machine is fitted with a special bin (12) or (12A) for
collecting the particles of CD/DVD/CREDIT CARDS and
separates them in order to allow for separate waste disposal.
AUTOMATIC FUNCTIONS
All models KOBRA 260TS, KOBRA 270TS, KOBRA 310TS come
equipped with the following automatic functions.
❍
PHOTO CELLS (3) or (3A) to start up the machine
automatically as soon as any sheets of paper or optical
media are inserted into the throat of the machine (2) or (2A).
❍
AUTOMATIC STOP when bag is full or door is open signalled
by illuminated optical indicator (9) or (10) on control panel.
❍
MOTOR SAVE which stops the machine working if it
overheats.(If the motor saver comes on,the machine rests for
at least 10/15 minutes after which time the device restarts
automatically).
❍
AUTOMATIC RETURN anti-jam system in case of accidental
insertion of paper in axcess of the maximum capacity of the
model,cuts off power to the motor and then puts the machine
into reverse for a few seconds in order to free the cutting
rollers.
❍
ENERGY SMART SYSTEM once 8 seconds have passed
since the last shredding,the machine goes on automatic
STAND-BY with zero power consumption as indicated by the
light (1) on the control panel.After four hours of not being
used,the machine automatically shuts down the mains power
supply.
CARE AND MAINTENANCE
The shredders in the KOBRA 260TS,KOBRA 270TS and KOBRA
310TS range need no special maintenance. However it is
recommended to oil the particle or HS shredder with the KOBRA
oil supplied with the machine as soon as the warning light(5)
comes on to ensure efficient shredding and prolong the life of
the cutting blades.
ACCESSORIES
AUTOMATIC OILER
The shredders in the KOBRA 260TS, KOBRA 270TS and KOBRA
310TS particle cut and HS High Security series can be fitted on
request with a special built-in AUTOMATIC OILER system (which
come as standard on the KOBRA 310TS) eliminating the need
for manual oiling of cutting knives.
Models fitted with the AUTOMATIC OILER are delivered together
with a 1 Litre oil container.
INSTALLATION (FIG.4)
When the machine has been taken out of the packaging,
position the machine head on the cabinet, insert the pipe (17)
into the connector (14). Take the oil container supplied with the
machine, unscrew the seal cap and discard, insert the oil pipe
(13) and tighten the cap completely (16).
OPERATION
Once the machine has been pluggen in to the mains power
supply,press the ON/OFF button (O),the light bar(P) comes on
and the machine is ready to use.
For the first few minutes,the warning light (5) fig.3 might be
flashing because the oil feeder pipe is not yet completely full.to
speed up the process and switch off the OIL warning light (5) run
the machine empty for 3 or 4 minutes by keeping the FORWARD
button (7) fig.3 pressed down.Now your shredder is ready with
oiled cutting blades.
The OIL warning light (5) fig.3 flashes to warn that there is no oil
the container.
REPLACING OIL CONTAINER FIG.4
Open the lid.
Remove the empty oil container (15) from its housing,unscrew
the lid (16) on the top of the container and remove the oil hose
(13).
Provide yourself with a new oil container,unscrew the seal and
dispose of it,insert the oil hose and tighten the lid (16).Replace
the new oil container (15) in its housing and close the lid.Now
your document shredder is ready for use again with oiled cutting
blades.
WARNING!! For the first few minutes,the warning light (5) fig.3
might be flashing because the oil feeder pipe is not yet
completely full.To speed up the process you can activate the
electronic eyes (3) or (3A) and run the machine empty for at least
3 or 4 minutes at a strtch or else keep the FORWARD button (7)
pressed down.
NEVER use synthetic oil, benzene based products or
aerosol lubricants of any kind inside or near the machine.
Fire hazard.
8