Maclaren techno xt Manual De Usario página 12

Instructions
IMPORTANT:
READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
YOUR CHILDREN'S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
1 TO OPEN THE BUGGY
A Release storage clip.
B Open out the buggy.
C Using foot, push the brake pedal down fully to engage
the primary locks.
CAUTION: Ensure that all locking devices are engaged
before use.
2 TO OPERATE BRAKES
A T O ENGAGE BRAKES: With foot, pull the brake levers
fully back.
B T O RELEASE BRAKES: Push the brake levers fully
forward.
CAUTION: Parking device shall be engaged during the
loading and unloading of children.
CAUTION: Ensure parking device is engaged before
leaving the buggy unattended.
3 TO OPERATE FRONT WHEEL SWIVEL LOCKS
A T O LOCK SWIVELS: Lift BOTH swivel locking levers.
B T O UNLOCK SWIVELS: Push down BOTH swivel
locking levers.
4 SEAT BELT/SHOULDER HARNESS OPERATION
WARNING:
AVOID SERIOUS INJURY FROM
FALLING OR SLIDING OUT. ALWAYS
USE THE CROTCH STRAP IN
COMBINATION WITH THE WAIST
BELT AND SHOULDER STRAPS.
TO FIT HARNESS:
A Pull shoulder straps over the childs shoulder then
attach to the waist clips by sliding strap loops onto
the hooks.
B Insert both waist clips into the clasp, shoulder straps
are secured once the clips are fastened.
C Adjust strap lengths by sliding buckles. Belt and harness
should be snug.
TO RELEASE HARNESS:
D P ress the button on both the front and back of the
clasp simultaneously to release.
5 TO FIT HEAD HUGGERS
Unclip shoulder straps from seatbelt clasp, remove strap
from buckle clip and feed straps through holes in head
hugger cushion (height can be adjusted by selecting upper
or lower holes). Reclip shoulder straps to seat belt clasp.
TO FIT HARNESS PADS (If Supplied):
A Lay open pad under shoulder harness strap.
B Fold pad over and secure adjustable straps.
6 TO OPERATE THE ADJUSTABLE LEGREST
A Raise leg rest.
B Push in the lever on the leg rest to lock.
C T o release, simply pull the lever back on base of
adjustable leg and allow the leg rest to return.
7 TO ADJUST SEAT RECLINE
A T O RECLINE SEAT BACK: Lift both hand grips to release
seat locks and slide the seat back to desired position.
Lower hand grips to engage locks on both sides.
B T O RAISE SEAT BACK: From rear of buggy push seat back
to original upright or desired intermediate position.
8 TO ATTACH THE HOOD
CAUTION: Overloading may cause a hazardous unstable
condition to exist. Maximum total capacity of hood pockets -
1.1 lb (0.5 kg).
A W ith buggy open clip the hood to the handle tubes just
above the retaining blocks.
B Wrap adjustable straps around handle tubes.
C Place rear apron behind seat back.
D E xtend hood and press down on side hinges to lock open.
TO TILT HOOD:
E Fully unzip back panel.
F Tilt hood forward.
G T he hood is removed by firmly pressing down the clip
release tabs.
9 TO ADJUST HANDLE LENGTHS
A Press triggers.
B S lide handles until triggers locate in one of 3 positions.
Release triggers to lock.
10 TO FIT THE RAIN APRON
A R eturn hood to non-tilted position before fitting
rain apron.
B Ensure visor is folded away beneath the hood.
C Place the apron over the hood front.
D Attach two eyelets (one each side) to the hood clips.
E A ttach the two eyelets (one each side) to the front legs.
11 TO FIT THE SHOPPING BAG
CAUTION: Overloading may cause a hazardous unstable
condition to exist. Maximum load 4.4 lb (2 kg) evenly
distributed. The buggy may be folded with the bag still
attached but all contents must be removed. Failure to do
this could damage buggy and contents of shopping bag.
A Place bag on the 'X' frame under seat with lowest edge
of bag at front.
B Attach front straps to front legs just below seat.
C A ttach rear straps to rear legs just above horizontal
tie bar.
12 TO FOLD THE BUGGY
Ensure visor is folded away beneath the hood.
Ensure the seat back is in its fullest upright position and
the hood (if fitted) is folded back.
Remove contents of shopping bag.
It is recommended that the harness is fastened before folding
the buggy.
A Using foot, lift up on footplate to release primary lock.
B Push down on secondary lock lever.
C Grip handles and push forward.
D C ompress folded buggy and engage the storage clip.
13 REMOVING AND REFITTING THE SEAT COVER
Remove hood, shoulder pads and seat retention straps from
buggy if fitted.
A T wist shoulder strap end buckles and feed through holes.
B T he waist harness back strap is fixed to the chassis
behind the seat. To remove, twist the buckles on each
end of the harness back strap and unthread from the
'D' rings attached to the chassis.
IMPORTANT: It is important that the strap be rethreaded
through the 'D' rings after the seat has been refitted.
Failure to do so will endanger your child.
C Feed crotch strap buckle through holes.
D Unclip seat cover retaining straps.
E Unfasten seat fabric from handle tubes and seat base.
F Slide fabric from seat back and base.
G W hen refitting seat fabric, insert seat back support
tubes into fabric flap.
H W hen refitting shoulder straps choose the fabric holes
appropriate to the child's size. Twist the buckles and
feed through seat cover, seat back and then through
holes in plastic seat back arms.
J W hen refitting seat fabric to seat base pass crotch strap
buckle through the hole in the seat fabric and then hole
in seat base.
en
3