Tabla de contenido
Enlaces rápidos
Tabla de contenido
Manuales relacionados para AccuBANKER QuadScan D470
Resumen de contenidos para AccuBANKER QuadScan D470
- Página 1 User Guide QuadScan D470 4 Way Orientation Detector...
- Página 2 Thank you for trusting AccuBANKER with your cash handling needs. In order to optimize the performance of your equipment, we encourage you to thoroughly read this user guide prior to use. AccuBANKER and its logo are registered trademarks of Hilton Trading Corp. All Rights Reserved.
-
Página 3: Tabla De Contenido
Table of Contents INTRODUCTION ...................... 4 BOX CONTENTS....................... 4 1. SAFETY INSTRUCTIONS ................... 5 2 . EQUIPMENT OVERVIEW ................... 7 3. OPERATION ......................9 3.1 Basic Operation ............. 9 3.2 Suspicious Bill Warning ..........10 3.3 Bill Positioning .............. 11 4. -
Página 4: Introduction
Introduction The D470 incorporates the most modern techniques for the evaluation and detection of counterfeit bills. This detector assesses in detail the security features that are present in each bill and determines if these are genuine or suspicious. The equipment automatically alerts the user both visually and audibly when a suspicious bill is identified. -
Página 5: Safety Instructions
1. Safety Instructions Warning Do not use this product in areas where it may be exposed to water or other liquids. Unplug this equipment from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. To reduce the risk of electric shock, do not disassemble this equipment. - Página 6 Safety Instructions cont. •Follow all warnings and instructions marked on the unit. •This equipment is meant to be operated in an indoor environment with proper ventilation. •Do not place near direct sunlight, heat sources or air conditioners. •This equipment should only be operated with the power cord supplied and the type of power source indicated in this user guide.
-
Página 7: Equipment Overview
2. Equipment Overview 5. USB Interface Port 1. LED Indicator Display 6. Power Adapter Connector 2. Feeding Channel 7. On / Off Power Switch 3. SD Card Port 8. Serial Port 4. Bill Exit Slot... - Página 8 Equipment Overview cont. 9. Green Indicator (Indicates bill accepted) 10. Red Indicator (Indicates suspicious bill) 11. Grips for the AccuStand metal base 12. AccuStand metal base (Optional Accessory / Sold separately) 13. Battery compartment (Battery Optional / Sold separately)
-
Página 9: Operation
3. Operation 3.1 Basic Operation Connect the power cable to the detector and then connect the adapter to the power outlet. When turning on the detector, it will proceed with a self-check routine that lasts 2 seconds. The display will light the green indicator which means the equipment is ready to check the bills. -
Página 10: Suspicious Bill Warning
Operation cont. 3.2 Suspicious Bill Warning This equipment checks the Magnetic (MG), Infrared (IR) , Watermark (WM), Ultraviolet (UV) and other characteristics of the bills analyzed. If any of these security features do not pass the authentication of the bill, a red indicator will display and two beep notifications sound. -
Página 11: Bill Positioning
Operation cont. 3.3 Bill Positioning - This equipment has the ability to verify the authenticity of bills in any of four positions. - For correct verification, the bill must be introduced into the feeding channel straight and aligned all the way to the left edge, as shown in Figure "A"... -
Página 12: Solutions To Operational Problems
4. Solutions to Operational Problems 4.1 Preventive Measures For optimal operation of the detector, take into account the following: 1. Avoid direct exposure to powerful sources of light as well as magnetic interference (ex. microwave, cell phone or WiFi devices), which will affect the sensors of the detector. -
Página 13: Maintenance
Solution to Operational Problems cont. 4.2 Maintenance CAUTION: Before performing any cleaning process, turn off the equipment and unplug it. Please note that problems or defects caused by lack of maintenance are not covered under the warranty. a) Cleaning of optical sensors It is important to periodically clean the optical sensors to prevent particles of paper or dust adhering to them. -
Página 14: Jamming
Solution to Operational Problems cont. 4.3 Jamming - Ensure there are no foreign objects that could accidentally fall into the equipment (clip, tape, etc. ) - To avoid jamming the bills, position them correctly in the feeding channel. - Make sure the bill does not have adhesive tape. - The bill cannot be very wrinkled or torn. -
Página 15: Ir Sensor Calibration
Solution to Operational Problems cont. 4.5 IR Sensor Calibration 1. Use conventional 80g office paper and cut it to the size of a USD bill (6 x 2.5 inch) to calibrate the equipment. 2. Turn on the unit. 3. Pass the white paper as if to scan a bill. 4. -
Página 16: Software Updates
Software Updates Steps to perform software update: Copy the programming software to a mini SD card. Turn off the detector. Insert the mini SD card into the update port at the back of the unit as the image shown. Turn on the detector. The two LED indicators in the display will flash intermittently during the programing process. -
Página 17: Specifications
Power Consumption: < 5W Dimensions: 5.7 in x 5.9 in x 3 in (14.5 x 15 x 7.6 cm) Weight: 1.15 lbs (0.52 Kg) All support provided from our North American office Monday - Friday 9:00 am - 5:00 PM EST 1-888-993-2228 [email protected]... - Página 18 www.accubanker.com...