Zircon MultiScanner i320 OneStep Manual De Instrucciones

MultiScanner
i320
®
OneStep
®
Multifunction Wall Scanner
The MultiScanner i 320 OneStep features three
® ®
scanning modes: WireWarning
Detection Indication
• STUD SCAN: Locates the center and edges of wood
and metal studs up to 3 ⁄ in. (19 mm) deep
4
Stud Scan Mode Indication
• STUD DEEPSCAN : Locates the center of wood
®
and metal studs up to 1 1 ⁄ in. (38 mm) deep
2
Stud Edge or Center Indication
• METAL SCAN: Detects and locates ferrous (magnetic)
metal (such as 1 ⁄ in. rebar) up to 3 in. (76 mm) deep
2
Middle Bars
and non-ferrous (non-magnetic) metal up to 1 ⁄ in.
1
2
(38 mm) deep
ACT
WireWarning detection automatically detects
®
Technology) Indication
and alerts of live AC wires in STUD SCAN,
Metal Mode Indication
STUD DEEPSCAN , and METAL SCAN modes.
®
When AC voltage is detected, the AC Wire Warning ®
icon will be displayed on screen.
Note: This product is intended for use in the
U.S.A. and Canada only.
1. INSTALLING THE BATTERY
Press battery door release in with your finger or a coin and lift up
to remove door. Connect 9-volt battery to cable. Place into the
compartment and press into place. Replace battery door and snap shut.
Battery will last approximately 2 years under normal conditions.
2. SELECTING THE MODE
Move selector switch to the desired mode: STUD SCAN for finding wood
or metal studs; DEEPSCAN for scanning walls over 3 ⁄ in. (19 mm);
® 4
or METAL SCAN for locating metal.
Unit will remain off if POWER BUTTON is not pressed.
6. WORKING WITH DIFFERENT MATERIALS
Wallpaper: The MultiScanner i 320 functions normally on walls covered with
®
wallpaper or fabric, unless the materials are metallic foil, contain metallic fibers,
or are still wet after application. Wallpaper may need to dry for several weeks
after application.
Freshly painted walls: May take one week or longer to dry after application.
If it is difficult to locate a stud in STUD SCAN mode on fresh paint, switch to
METAL SCAN mode to locate nails or drywall screws holding drywall to studs.
Lath & plaster: Due to irregularities in plaster thickness, it is difficult for the
MultiScanner ® i 320 to locate studs in STUD SCAN mode. Change to METAL
SCAN mode to locate the nail heads holding wood lath to the studs. If the
i
plaster has metal mesh reinforcement, MultiScanner ® 320 will be unable to
detect through that material.
Extremely textured walls or acoustic ceilings: When scanning a ceiling or wall
with an uneven surface, place thin cardboard on the surface to be scanned and
scan over the cardboard in STUD DEEPSCAN ® mode. If irregular scanning results are
received, switch to METAL SCAN mode to locate nails or drywall screws that line up
vertically where a stud or joist is positioned.
Wood flooring, subflooring, or gypsum drywall over plywood sheathing:
Use DEEPSCAN mode and move the tool slowly. The Signal Strength Indicator
®
may only display 1 or 2 bars when the tool locates a stud through thick surfaces.
i
MultiScanner ® 320 cannot scan for wood studs and joists through carpet and
padding. In problematic situations, try using METAL SCAN to locate nails or screws
that may line up vertically where a stud or joist is positioned.
Note: Sensing depth and accuracy can vary due to moisture, content of materials,
wall texture, and paint.
FCC Part 15 Class B Registration Warning
This device complies with Part 15 of FCC Rules. Operations subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired protection.
SpotLite Signal Strength
®
Pointing System Indicator
LCD Display
®
™ (Auto Correcting
Mode Selector Switch
Power Button
Running Board
Battery (back of unit)
7. SCANNING IN METAL MODE
Note: When scanning for studs, use STUD SCAN mode (or Stud DEEPSCAN
Figure A
to quickly locate the center and edges of wood or metal studs. Use METAL SCAN to determine
if the previous reading in STUD SCAN was a wood stud, metal stud, or pipe. In METAL SCAN,
only metal drywall screws will be found in wood studs, while metal will be indicated everywhere
on a metal stud or pipe.
METAL SCAN has interactive calibration that allows you to adjust its sensitivity to metal, which can
be used to find the precise location of metal objects in walls, floors, and ceilings. Maximum sensitivity
is ideal for quickly finding the approximate location of metal. However, sensitivity can be reduced by
calibrating the tool closer to metal. With reduced sensitivity, the area where metal is indicated will
be smaller. But in both cases, the metal target is in the center of the area where the tool indicates
metal is present.
1. Move mode switch to METAL SCAN mode. For maximum metal sensitivity, turn the tool on in the
air by pressing and holding the power button. This will ensure that it calibrates away from any metal
Figure B
objects. (The tool can only be calibrated off the wall in METAL SCAN mode.)
2. (Figure A) While holding the power button, press the tool flat against the wall and slowly slide the
scanner across the surface. Mark the point where you get the highest metal indication (the most Middle
bars on the screen). If it is a strong target, the SpotLite
and a steady beep will sound. Continue in the same direction until display bars reduce. Reverse direction
and mark the spot where the display bars peak from the reversed direction. The midpoint of the two
marks is the location of the center of the metal object.
If the unit indicates metal over a large area, you can refine the scanning area to more accurately locate
the metal target by following steps 3 and 4 below.
3. (Figure B) To further pinpoint the location of the metal target, scan the area again. Release the
power button and then turn the unit back on, this time starting on the wall over one of the previous
marks. This will reset the tool to a lower sensitivity and narrow the scan area.
Figure C
4. (Figure C) To continue to reduce sensitivity and further refine the scanning area, repeat step 3.
This procedure can be repeated multiple times to narrow the field even further.
Note: If any bars display on the screen, metal is present. Small targets or targets deep within the surface
may only illuminate some of the bars and not the center line or audio tone. In this case, use the highest
indication to determine the metal position.
3. FINDING A STUD 4. OPERATING TIPS
Always scan for studs with the scanner placed
For optimum scanning results, it is important to properly hold the MultiScanner
flat against the wall. Move the mode switch to
more accurate scanning results:
STUD SCAN, place the tool flat against the wall,
• Grasp the handle with your thumb on one side and your fingers on the other side. Make sure your fingertips are resting on or above the running
then press and hold the Power button.
board and not touching the surface being scanned or the scanning head of the tool.
Wait for beep to confirm calibration has
• Hold the tool straight up and down, parallel to the studs, and do not rotate the tool.
completed before moving scanner.
• Keep tool flat against the wall and do not rock, tilt, or press hard when slowly sliding across the surface being scanned.
Slowly slide tool across
• Avoid placing your other hand, or any other part of your body, on the surface being scanned. This will interfere with the tool's performance.
surface. EDGE display
WireWarning
®
will illuminate, indicating
Zircon's WireWarning
location of the stud edge.
appear in the display. If scanning begins over a live AC wire, the AC indicator will flash continuously. If this occurs, release the Power button,
move the tool over, and recalibrate in a new location. Once calibration has completed, begin to slide the tool in the direction of your initial calibration.
CAUTION: Wires deeper than 2 in. (51 mm) from the surface, in plastic conduit, or behind plywood shear wall, or metallic wall covering
Continue sliding tool.
may not be detected. Metal shielded wires or those in metal conduit will not be detected. Use extreme caution under these circumstances
When the center of
or whenever live AC wiring is present.
a stud is located
Always turn off power when working near electrical wires.
with three bars on
the Signal Strength
5. CALIBRATING THE TOOL IN STUD SCAN/STUD DEEPSCAN
Indicator, the four
MultiScanner i
®
Middle bars, CENTER
when needed, to successfully find the center of studs in one step.
display, and SpotLite
®
• Place MultiScanner
Pointing System will
all illuminate and
• Once powered on, tool will automatically perform all calibrations. The LCD will display all icons until calibration is complete. Upon completion of calibration, the SpotLite
the buzzer will sound.
Pointing System and buzzer will momentarily activate and the tool will begin continuous measurements. Continue to press power button down and keep the tool flat against
the wall and begin scanning.
Note: It is important to wait for calibration to complete (1–2 seconds) before moving the scanner.
In cases of deeper studs
(thicker walls), when the • ACT ™ (Auto Correcting Technology)—During scanning, the tool will automatically recalibrate itself when needed.
This recalibration is transparent and no indication is made. If an arrow icon illuminates, the tool calibrated near
center of the stud is
located only two bars or over a stud and then moved away. The arrow indicates the direction of the missed stud.
will show on the Signal
Strength Indicator and
only the SpotLite ®
Pointing System and
four Middle bars will
illuminate. If you still
can't locate a stud,
try STUD DEEPSCAN mode.
®
mode on thicker walls)
®
Pointing System will also shine a beam of light
®
i
® 320 and move slowly when scanning. The following tips will provide
Detection
detection feature works continuously in all modes. When live AC voltage is detected, the AC detection warning indicator will
®
®
320 can be calibrated anywhere on the wall. It provisionally monitors the subsurface environment 10 times per second and automatically recalibrates,
i 320 against the wall before pressing the Power button in STUD SCAN or STUD DEEPSCAN
®
8. HELPFUL HINTS
(See also number 4, OPERATING TIPS)
Situation Probable Cause
Detects other objects • Electrical wiring and metal/plastic pipes may
besides studs in be near or touching back surface of wall.
STUD SCAN mode.
Finds more targets
than there should be.
Difficulty detecting • Tool calibrated over metal object.
metal. • Metal targets too deep or small.
Image of metal object • Metal has greater density than wood.
appears wider than
actual size.
Constant readings of • Double and triple studs are usually found
studs near windows around doors and windows. Solid headers
and doors. are above them.
You suspect electrical • Wires are shielded by metal conduit,
wires, but do not a braided wire layer, or metallic wall covering.
detect any. • Wires deeper than 2 inches (51 mm) from
surface might not be detected.
• Wires may not be live.
ACT, CenterVision, DeepScan, MultiScanner, OneStep, SpotLite, WireWarning, and Zircon are registered trademarks or trademarks of Zircon Corporation.
Visit www.zircon.com/support for the most current instructions.
LIMITED 1 YEAR WARRANTY
Zircon Corporation, ("Zircon") warrants this product to be free from defects in materials
and workmanship for one year from the date of purchase. Any in-warranty defective product
returned to Zircon*, freight prepaid with proof of purchase date and $5.00 to cover postage
and handling, will be repaired or replaced at Zircon's option. This warranty is limited to
the electronic circuitry and original case of the product and specifically excludes damage
caused by abuse, unreasonable use or neglect. This warranty is in lieu of all other warranties,
express or implied, and no other representations or claims of any nature shall bind or
obligate Zircon. Any implied warranties applicable to this product are limited to the one
year period following its purchase. IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM POSSESSION, USE OR
MALFUNCTION OF THIS PRODUCT.
In accordance with government regulations, you are advised that: (i) some states do not
allow limitations on how long an implied warranty lasts and/or the exclusion or limitation
of incidental or consequential damages, so the above limitations and/or exclusions may not
apply to you, and further (ii) this warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
mode.
®
®
Solution
• Scan the area in METAL SCAN mode to determine if metal is present.
• Check for other studs equally spaced to either side (12, 16, or 24 inches [305, 406, or 610 mm])
apart or the same stud at several places directly above or below the first scan area.
• A stud reading would measure approximately 2 inches (51 mm) apart from each edge; anything
larger or smaller is most likely not a stud if not near a door or window.
• The scanner may have been calibrated over a metal object, reducing sensitivity.
Try calibrating in another location.
• Scan in both horizontal and vertical directions. Metal sensitivity is increased when
metal object is parallel to sensor, located under Zircon logo.
• To reduce sensitivity, recalibrate MultiScanner i 320 over either of first two marks
®
(Metal mode only–See Step 7).
• Detect outer edges so you know where to begin.
• Try METAL SCAN to see if you can find metal, wire, or metal conduit.
• Try turning on switches to outlet.
• Try plugging a lamp into outlet and turning on switch.
Return product freight prepaid with proof of purchase date (dated sales receipt) and $5.00
to cover postage and handling, to:
Zircon Corporation
*Attn: Returns Department
1580 Dell Avenue
Campbell, CA 95008-6918 USA
Be sure to include your name and return address. Out of warranty service and repair, where
proof of purchase is not provided, shall be returned with repairs charged C.O.D. Allow 4 to 6
weeks for delivery.
Customer Service, 1-800-245-9265 or 1-408-963-4550
Monday–Friday, 8:00 a.m. to 5:00 p.m. PST
E-mail: [email protected]
U.S. Patents 6023159, 6259241, 6989662, 7116091, and 7148703, Canadian Patents 2141553,
2341385, and Patents Pending, Japanese Patents 3581851, 4152361, and Patent Pending,
German Patent 693338849, French and U.K. Patents 657032, and E.U. Patents Pending
©2009 Zircon Corporation • P/N 60943 • Rev A 02/09