Fenix THERM 350 Instrucciones Para La Instalación página 8

If the thermostat is set as a floor thermostat (F), it displays the current tem-
perature in the floor.
If the thermostat is set as a room thermostat (R), it displays the current
temperature in the room.
If the thermostat is set as a room and floor thermostat, (R&F) it displays the
current temperature in the room.
Frost protection programme
This programme is designed for long absence. When this program is selec-
ted, the thermostat will regulate by this set value. All other set values and
settings will remain in memory and the thermostat will go back to them
when this program will be deactivated. The temperature can be between 5
and 15 C. Factory set temperature is 10°C.
°
•
1. Press The display shows
.
2. Press  repeatedly until the display shows
3. Press repeatedly until the display shows repeatedly until the display shows

4. Now the selected temperature is flashing.
5. Press  or  to select the set value. Confirm with
To activate this programme:
•
1. Press The display shows
.
2. Press  repeatedly until the display shows
One of the icons for preset programmes will flash, depending on the current
setting. (If no icon flashes, no preset programme is selected).
3. Press  to select . Confirm with
If a preset programme is selected the programme starts up.
together with and indicates that the programme is running.
Display contrast
•
1. Press The display shows
.
•
2. Press The display shows 1,2, 3.......8 depending on actual setting.
.
3. Press or to change the contrast. Confirm with
 ,
Adaptive function
The thermostat is equipped with a so-called adaptive function, which means
that if you have programmed the thermostat to keep a certain temperature
at a certain time, the thermostat will calculate itself when to start heating
so that the floor surface will keep the set temperature at the preset time.
Factory set is ON.
To deactivate the adaptive function:
•.
1. Press The display shows
2 Press repeatedly until the display shows

.
3 Press  repeatedly until the display shows "AF". Press
.
4. The display shows the actual settings. Press
Operation time
The thermostat can show the operation time in percent for the last 24 hours,
7 days, 30 days or 365 days. To see the percentage operation time:
1. Press • The display shows
.
2. Press  repeatedly until the display shows
The display shows operation time in percent for the last 24 hours.
3. Press . The display shows

7 days.
4. Repeat the steps above to show the operation time for the last 30 days or
365 days, respectively.
Ventilation mode
If the measured temperature is reduced by more than 3°C during one minu-
te, the thermostat is automatically put in ventilation mode. The thermostat
stops heating for 15 minutes. When 15 minutes have passed, the thermostat
returns to normal mode.
The ventilation mode is always active, regardless of which programme is
running.
Troubleshooting
When an error occurs, the thermostat will switch off the heating. The LED
flashes alternately in red and green. The LCD-display shows a flashing error
code, the display shows according to below:
Error 1: Short circuit room sensor.
Error 2: Interruption room sensor.
Error 3: Short circuit floor sensor.
Error 4: Interruption floor sensor.
The supply cord of this control can be replaced only by the manufacturer or
his accredited service agent.
.
•
Press
. .
•
Press .
.
•.
.
. •
Press
.
•
.
.
•
.
.
•.
Press
.
•
Press
.
Press  to change. Confirm with
.
•
. Press
.
and operation time in percent for the last
Installation instructions FENIX Therm 350 English Page 3/3, 071217
Technical specifications
Voltage
Air temperature range
Floor temperature range
Temperatur limiter
Breaking capacity
Connection cable
Load
Hysteresis
Protection class
Run reserve
° C
Colour
Background lighting
Max length sensor cable
The LED's indication:
Green
Red
Flashing green and red light
Adapted for Eljo Trend, Elko RS, Strömfors and Merten frame-systems.
EMC-certified and can handle an overvoltage of 2 500 VAC.
is shown
Safety standard: CE
Fulfils the RoHS and WEEE-directive
FENIX Therm 350 with accessories
Article
FENIX Therm 350
Extension frame
Sensor cable 3 m (included in the pack)
Back plate, polar white
Model no. 66 210 84
Type IB
Degree of pollution 2
Rated impulse voltage = 4000V
Size of terminal 2,5 mm
•
.
Start / Stop set back programme
This will not erase settings, will only start and stop set back
programme.
Start programme:
1. Press • . Display shows
2. Press  repeatedly until display shows
If a programme is active one icon is flashing
3. Press or
 
flash. Confirm with
Stop programme:
•
1. Press . Display shows
2. Press repeatedly until display shows

If a programme is active one icon is flashing
3. Press  or 
230 VAC-50 Hz
5-37 º C
5-37 º C
5-45 º C
3600W / 16A / 230 VAC
max 2,5 mm
2
φ
cos = 0,3
+- 0,3 º C
IP21
36 hours
Polar white as standard, aluminium
and bronze as option
Shines 30 seconds after the last
button is pushed
45 m, 2 x 1,5mm 2
230 VAC supply connected
Floor heating cable operating
Error indication
2
.
. Press
repeatedly to choose icon, chosen icon must
•
.
.
. Press
,
repeatedly until no icon flash. Confirm with
Dimensions (mm)
81x81x40
81x81x18
86x86x6
•
.
.
, , ,
•
.
.
, ,
•
.