Good Earth Lighting Downfire SE1084-WH3-02LF0-G Manual Del Usario

Wall plate
Plaque murale
Placa de pared
Motion Sensor (PIR) Head
Tête du détecteur de
mouvement passif
à infrarouge (PIR)
Cabeza del sensor
de movimiento (PIR)
The Good Earth Lighting Downfire
TM
activates at sundown and provides ~750 lumens of low light for either 3 hours, 5 hours or all night, depending on the setting. The Area Light Mode can also be shut OFF. The
Security Light Mode activates durring night time hours, but is only activated when motion is detected. When motion is detected the light output is boosted to ~2500 lumens of
full brightness. Please read the full instructions for more detail.
1. Shut off power at the circuit breaker or fuse panel before removing the old fixture or installing the new one.
2. DO NOT USE THIS FIXTURE IN A CIRCUIT HAVING A DIMMER CONTROL IN THE CIRCUIT.
3. This fixture can only be installed over a recessed junction box, OR a UL Listed surface mount electrical box rated for wet locations. Recessed electrical box
installations REQUIRE the outer edge of the wall canopy to be completely sealed with silicone RTV glue, and surface mount junction boxes require the use of the
foam gasket (included), to prevent water seepage into the wall canopy. Without sealing the canopy enclosure, water seepage can short out the driver, and cause
product failure, and/or other safety issues.
4. NOT FOR EAVE MOUNTING ONTO PERFORATED EAVE MATERIAL with a recessed junction box. Doing so can allow water to seep into the fixture canopy and result
in a hazardous situation and/or fixture failure.
5. LEDs can be damaged by electrostatic discharge shock. Before installation, discharge yourself by touching a grounded bare metal surface to remove this
hazard. For electrical requirements, see fixture.
6. Minimum 90°C supply conductors. For fixture electrical ratings, see fixture label.
7. If unsure if the junction box is properly grounded, or the box is plastic and has no ground wire, or are unfamiliar with the methods of properly grounding fixture,
consult a qualified electrician.
8. This security light uses passive infrared (PIR) technology to automatically turn on the light. Passive infrared does not detect motion, per se, but operates by sensing
differences in ambient temperatures, versus warmer objects in its field of view. As such, the sensor can be set off by a variety of other sources, including dryer
vents, hot tubs, and the like. Select the installation location carefully, and do not aim the PIR toward areas having frequent pedestrian or motorized traffic, and/or
other objects that generate areas of warmer air. All of these may trigger the motion sensor security light and may be disruptive to the intended operation of the light.
9. PIR sensors may not work as expected in conditions where there are temperature extremes; either very cold, or very hot outside. Because PIRs operate
by sensing differences in body temperature vs. ambient temperature, extremes in ambient temperature can affect the operation of the PIR.
10. PIR sensors are NOT capable of seeing through glass. As such, it is not recommended that light fixture be mounted behind a glass window, or door.
11. Do NOT install near other sources of light, which can fool the built-in light sensor into thinking it is daylight, and may prevent the proper operation of the light.
TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH TO J-BOX OFF
INSTALLATION FOR ROUND SURFACE
1
SURFACE
MOUNT JUNCTION BOXES
AA/BB
x2
FF x1
GG x1
1 SURFACE Pull supply wires out of the junction box (j-box). With the side marked "FRONT" facing out, attach the mounting strap (FF) to the j-box with machine screws
(AA or BB). Remove the protective liner from adhesive side of the gasket (GG). Guide the j-box wires through the gasket opening. Align the center holes of
the gasket and mounting strap and apply the gasket to the outer edge of round edge of the j-box.
1 RECESSED Pull supply wires out of the junction box (j-box). With the side marked "FRONT" facing out, attach the mounting strap (FF) to the j-box with machine screws
(AA or BB).
DD x1
Light head
Tête de la lampe
Cabeza de luz
2N1
SECURITY LIGHT AREA LIGHT
(High Beam) (Low Beam)
PIR control panel
Range
30 60 1 5 3hrs 5hrs
Panneau de commande
5 Max. Test 10 OFF Dusk To Dawn
Feet Minutes
du système PIR
Panel de control del PIR
security light functions in two modes, Area Light Mode (~750 lumens) and Security Light Mode (~2500 lumens). The Area Light Mode
WARNINGS AND CAUTIONS
Fixture must be properly
grounded. Connect fixture
ground wire to ground wire in J-
box using wire nut (DD). These
wires can either be green or
bare copper. Insert black supply
lead into connector on black
fixture wires and white supply
lead into connector on white
fixture wires. Push excess wire
and wire connections back into
J-box. Orient sensor and light
heads properly to prevent water
from damaging the fixture.
Downfire™ 2N1 Security and Area Light
Éclairage de sécurité et projecteur 2N1 Downfire™
Luz de seguridad y de área Downfire™ 2N1
Model / Model / Modelo #: SE1084-WH3-02LF0-G, SE1084-BP2-02LF0-G
Hardware kit* / Kit de petit matériel de fixation*/
Kit de herrajes*
CC
AA
BB
x1
x2
x2
EE FF
GND
x1 x1 FRONT
* Actual hardware may differ from illustration
* La quincaillerie incluse peut être différente de l'illustration.
* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
AA/BB
x2
FF x1
SENSOR ORIENTATION
SENSOR HEAD ORIENTATION
45°
MAX.
CONTROL PANEL
FACING DOWN
The (PIR) sensor head must be oriented
specifically to prevent water from entering.
The control panel (located on the under side of
the sensor) MUST face down toward the ground
at all times to prevent water from entering and
damaging the unit.
NEVER ANGLE THE SENSOR HEAD
BELOW A 45° DOWNWARD ANGLE
(Page 1)
(Page 4)
(Página 7)
Required
Nécessaire
DD
Se necesita
x1
GG
x1
INSTALLATION FOR RECESSED
JUNCTION BOXES
LIGHT ORIENTATION
LIGHT HEAD ORIENTATION
Light heads must be oriented with"THIS
SIDE UP" pointing upward.
Make sure each light head has this marking
pointing upward at all times to prevent water
from entering and damaging the unit.
Silicone
Silicone
Silicona