Sabo BC-30 Manual Del Operador página 26

STARTING/STOPPING THE TRMMER
See figure 6
•
In order to start the grass trimmer, hold down the safety lock (1) and press the switch (2).
•
To start the trimmer, release the switch (2).
WARNING
Noise: A certain amount of noise from the machine is unavoidable. Loud work is only permitted at certain times. Observe the quite periods and limit
working time to a minimum. For personal protection and to protect other workers nearby, appropriate ear protection must be worn.
Vibration: Always wear safety and anti-vibration gloves. Excessive vibrations can cause Raynaud's syndrome or carpel tunnel syndrome. If you experience
an unpleasant feeling while using the machine or if the skin on your hands discolours, stop working. Schedule reasonable rest periods. Frequent and
regular users should carefully check the conditions of their hands and fingers.
WARNING
Keep the trimmer away from the body at all times and keep your distance. Any contact with the trimmer cutting head while it is in use can lead to serious
injuries.
TIPS FOR CUTTING
See figure 7
•
Keep the trimmer head at an angle to the area being cut. This achieves the best cutting results.
•
The trimmer cuts better if it is moved from right to left across the cutting area; it is less effective if it is moved from right to left.
• Use the end of the thread for cutting. Do not push the thread head into uncut grass.
•
Cutting into wires and lattice fences leads to increased thread wear and this results in the thread being cut off. Stone and brick walls, kerb stones and wood can also lead to very
fast wearing of the thread.
•
Avoid cutting trees and bushes. Tree bark, wooden ornaments, external wall claddings and fence posts can be easily damaged by the thread.
FEEDING THE THREAD
When the trimmer is being used, the cutting thread becomes worn and shorter. This trimmer is fitted with a thread feed with plug button. The thread is lengthened by hitting the thread head
against the ground during use. The thread cutter shortens the thread in order to achieve the optimum thread length.
THREAD CUTTER
The trimmer has a thread cutter on the grass deflector. In order to achieve optimum cutting results, push the thread forwards until it is cut to the right length by the thread cutter. Feed thread
every time you hear that the motor is running faster than normal or if the cutting performance deteriorates. This maintains the optimum performance and the thread is long enough that it can
be fed properly.
CONVERT GRASS TRIMMER INTO AN EDGE TRIMMER
See figure 8
•
Remove the battery.
•
Press down the locking button (1) and keep it in this position.
•
Turn switch (2) by 90° until it locks.
•
Release the locking button (1).
WARNING
Only use original spare parts when replacing parts. The use of other parts can lead to danger or damage your device.
WARNING
To avoid serious injuries during cleaning or to carry out other maintenance work, always remove the battery from the tool first.
GENERAL MAINTENANCE AND CARE
The product should be inspected for damaged, missing or loose parts, such as screws, nuts, bolts, covers, etc. before every use. Tighten all the fastenings and covers and do not use the
product until all the missing or damaged parts have been replaced. Do not use solvents to clean plastic parts. Most plastics can be damaged by different types of commercial solvent. Use a
clean cloth to remove dirt, dust, oil, lubricants etc.
WARNING
Never allow brake fluids, petrol products based on oils, etc. come into contact with plastic parts. Chemicals can damage, weaken or destroy plastic, which
can lead to serious injuries.
Only the parts listed in the spare parts list are envisaged for repair or replacement by the customer. All other parts have to be replaced by the authorised customer service.
WARNING
To avoid serious injuries during cleaning or to carry out other maintenance work, always remove the battery from the tool first.
REPLACING THE COIL
See figure 9
To achieve the best cutting results, only use original mono-filament threads.
• Remove the battery.
•
Press the two catches on the side of the coil lid.
•
Pull the coil holder up in order to remove it.
•
Remove the old coil.
26