RS 182-578 Hoja De Instrucciones página 6

V9671
When cutting from within a workpiece (figure 15), drill a suitable
size hole first. Do not plunge cut.
Before sawing metal, spread a thin film of cooling agent such as oil,
along the proposed cutting line.
The sawing speed can be controlled through the transformer. As a
general guide use:
Slow speed for metals
Medium speed for hardwoods and plastics
Fast speed for softwoods
If cutting becomes difficult, this may be a sign that the blade is
becoming blunt. Change the blade being used as seen in figures
13 and 14.
Always use minimum pressure on the blades. Let the tool do the
work, otherwise breakage can occur.
Remember to always switch the tool off when the work is finished.
Maintenance
Occasionally apply a drop of oil on the reciprocating shaft (figure 11 f).
Always keep the air vents (e) free from obstruction.
This electric tool complies with the requirements in force relating to
radio and TV interference.
Engraving pen
RS stock no. 182-685
Engraving kit
RS stock no. 182-679
Technical specification
Voltages
RS stock no. 182-685 ______________________________9-16V
RS stock no. 182-679 ______________________220/240v; 50Hz or
____________________________120v, 60Hz
Maximum output
RS stock no. 182-685 __________________________________6W
RS stock no. 182-679 ______________________3.6W peak & 1.8W
________________________________continuous
No load speed __________________________12,500
Shaft holder capacity ________________________________2.35mm
Cable type________________________________________standard
Cable length:
RS stock no. 182-685 __________________________________1.8m
RS stock no. 182-879 __________________________________1.7m
Weight:
RS stock no. 182-685 __________________________________75g*
RS stock no. 182-679 __________________________________68g*
*Weight of pen and cord only
General introduction
You are now in possession of a quality precision engraving pen. Please
read these operating and safety instructions carefully before use.
Please check you have the following items:
RS stock no. 182-685 Engraving pen
1 Diamond bit, diameter 1.4mm.
RS stock no. 182-691 Engraving & security kit
1 Diamond bit, diameter 1.0mm
1 Grinding stone - taper
1 Plastic stencil
1 Grinding stone - cylinder
User instructions
1. This RS engraving pen has been designed for engraving glass,
metal, ceramic and stone.
2. Your engraver can take bits of 2.35mm in diameter.
3. You can easily fit and remove engraving bits by simply pushing and
pulling them in and out of the shaft holder (C) by hand.
6
4. Your pen will automatically switch off when you remove your finger
or thumb from the switch (B) and will switch on when you press the
switch.
5. You can use any RS transformer shown in this leaflet with your RS
stock no. 182-685 engraving pen.
Engraving with your engraver
Hold your engraving pen as you would hold an ordinary pen.
It is advisable to engrave at an angle to the workpiece. This will
give you the best control and stop skidding.
Maintenance
Please oil shaft holder (C) regularly to ensure longer life and smoother
running of your engraver.
This electric tool complies with the requirements in force relating to
radio and TV interference.
Variable speed transformer
RS stock nos. 182-691
Technical specification
____________________________________RS stock no. 182-691
Available
primary voltages ________________________________240v, 50Hz
Secondary voltage ______________________________9 -16V
Outputs____________________________________________24VA
Speed control range (rpm) ________________7000-30,000
Cable type ______________________________________Standard
Usage __________________________________All RS 12V tools
General information
Your variable speed transformer is equipped with a re-settable overload
cut-off facility. This overload facility protects your unit from current
loading and over heating. If the transformer is overloaded, the re-
settable fuse system will be activated and the neon indicator light (d)
will go out. Any 12V precision tools connected to the transformer
should be switched off. A short period of cooling time should be
allowed (approx. 3 minutes) before pushing the reset button (c). The
/min (12v)
neon indicator light will re-light, allowing work to continue.
Important General safety
1. Do not use or store transformer and 12V units in damp or wet
conditions.
2. Before changing 12V units, always switch off the transformer.
3. After use, always disconnect the power supply.
4. Always wear safety glasses when working with RS precision tools.
5. Do not undertake repairs on the transformer yourself.
6. Do not leave your tools and transformer unattended while switched
on.
This electric product complies with the requirements in force relating to
radio and TV interference.
Vertical drill stand
RS stock no. 182-714
*Please read these operating instructions carefully before use.
Your RS stock no. 182-714 vertical drill stand has been designed to
enable precision vertical drilling using any one of the RS range of
precision drills, shown in this leaflet.
Assembly of unit
1. Place the pressure bolt into the hole on the top of the stand. Screw
into place until it becomes tight and the groove is in line with the
plane of the handle.
2. Place the handle in the left hand lug on the top of the stand (as
shown). Screw in the pivot screw from the rear of the stand until it
becomes flush with the front surface of the lug.
/min