Chicago Pneumatic CP9362 Serie Manual Del Usuario página 3

EN
English
1. Technical Data (see Fig 3.)
Blows per
mInute
Model
1
[min-1]
max pressure 6.3 bar (90 psi)
a :Vibration level, k Uncertainty ; L
hd
Declaration of noise (ISO 15744) and vibration emission (ISO 28927-10)
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared va-
lues of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured
in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way
the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user.
We, CHICAGO PNEUMATIC TOOLS , cannot be held liable for the consequences of using the declared values, instead of values refl ecting the actual exposu-
re, in an individual risk assessment in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at www.
pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf
We recommend a programme of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that management proce-
dures can be modifi ed to help prevent future impairment.
2. Machine Type
• This product is designed for removing material using a chisel or suitable needles. No other use is permitted. For professional use only.
• Please read the product safety information carefully!
3. Implementation and Operation
• Fix the accessories properly to the tool.
• Connect device as shown in Fig.1.
• To start the machine, simply pull the trigger (A). Machine speed is increased by increasing pressure on the trigger. Release the trigger to stop.
• Remember that it is always the tool that must do the work. There is no need for the operator to apply extra pressure on the tool when it is working. Maintain
the contact with the work surface by applying enough pressure to stop the tool from bouncing.
• Always shut off air supply, drain hose of air pressure and disconnect tool from air supply when not in use, before changing accessories or when making
repairs.
4. Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two (2) drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once
a day.
Recommended lubricant CP Oil PROTECTO-LUBE:
- 4 oz (0.12l) P/N: CA149661
- 20.8 oz (0.591l) P/N: CA000046
- 1gal (3.8l) P/N: P089507
5. Maintenance
• Follow local country environmental regulations for safe handling and disposal of all components
• Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn parts.
• Always ensure that the machine is disconnected from energy source (compressed air) to avoid accidental operation.
• High wear parts are underlined in the parts list.
• To keep downtime to a minimum, the following service kits are recommended:
Tune-Up Kit: see part list
6. Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
Technical fi le available from EU headquarter. Nicolas Lebreton R&D Manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Copyright 2015, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and
drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
ORIGINAL TEXT
Stroke & bore Weight
2 3
[mm] [mm] [lb] [kg]
Sound pressure level dB(A), K
pA
CP9362, CP9363 & CP9373 Series
Inner hose
Dimension
L x W x H
diameter
W
L
4 5
[inch.] [mm] [inch.] [mm]
= K = 3 dB Uncertainty.
pA WA
Chipping Hammers
Sound Sound-
Air inlet pressure power
L L
pA wA
6 7 8
[inch] [dB(A)] [dB(A)]
Vibrations
ahd k
9
[m/s²] [m/s²]